manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

Peripheral Units (Vol. 2 of 2)

Synchronous Serial Interface (SSC)

 

User’s Manual

20-46

V2.0, 2007-07

SSC, V2.1

 

20.3

SSC0/SSC1 Module Implementation 

This section describes SSC0/SSC1 module interfaces with the clock control, port
connections, interrupt control, and address decoding.

20.3.1

Interfaces of the SSC Modules

Figure 20-16

 shows the TC1796-specific implementation details and interconnections of

the SSC0/SSC1 modules.

Figure 20-16 SSC0/SSC1 Module Implementation and Interconnections

MCA05791

Clock

Control

Address

Decoder

Interrupt

Control

f

SSC0

Address

Decoder

Interrupt

Control

To
DMA

f

CLC0

f

SSC1

f

CLC1

Clock

Control

SSC0_RDR

SSC0_TDR

To
DMA

SSC1_RDR

SSC1_TDR

Port 2

Control

. . 
.

MRSTB
MTSR

Master

SLSI1

SLSO[7:2]

MRSTA

MTSRB
MRST

MTSRA

SCLKB
SCLK

SCLKA

Slave

Slave

Master

Slave

Master

Port 6

Control

MRSTB
MTSR

Master

SLSO[7:2]

MRSTA

MTSRB
MRST

MTSRA

SCLKB
SCLK

SCLKA

Slave

Slave

Master

Master

MTSR0

MRST0

SCLK0

P6.5 /
MRST1

P6.4 /
MTSR1

P6.6 /
SCLK1

SLSI0

P2.2 /
SLSO2

P2.7 /
SLSO7

P6.7 /
SLSI1

SLSI[7:2]

1)

SLSI1

Slave

SLSI[7:2]

1)

SSC Enabled

M/S Selected

SLSO0

SLSO1

1) These lines are not connected

SLSO1

SLSO0

SSC0

Module

(Kernel)

8-Stage RXFIFO

8-Stage TXFIFO

SSC1

Module

(Kernel)

EIR
TIR
RIR

EIR
TIR
RIR

A2

A2

A2

A2

A2

A2

A2

A2

A2

A2

A2

A2

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Brand: ABB Pages: 370
ABB EAN823 Instructions Manual preview
EAN823
Brand: ABB Pages: 17
ABB COM600 series User Manual preview
COM600 series
Brand: ABB Pages: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Brand: ABB Pages: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Brand: ABB Pages: 42
Daikin BRC1H71W Installation Manual preview
BRC1H71W
Brand: Daikin Pages: 38
Daikin BRC1H71W Operation Handbook preview
BRC1H71W
Brand: Daikin Pages: 2
Daikin BRC1E72 Operation Manual preview
BRC1E72
Brand: Daikin Pages: 148
Daikin EHVH04S18CA Operation Manual preview
EHVH04S18CA
Brand: Daikin Pages: 12
Daktronics RC-100 Operation Manual preview
RC-100
Brand: Daktronics Pages: 52
Waeco RC-100 Installation And Operating Instructions Manual preview
RC-100
Brand: Waeco Pages: 20
Z-Wave RC-100 Operating Instructions Manual preview
RC-100
Brand: Z-Wave Pages: 56
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Brand: Lattice Semiconductor Pages: 26
Datavideo RMC-230 Instruction Manual preview
RMC-230
Brand: Datavideo Pages: 17
Datamax I-Class Installation And Operating Instructions Manual preview
I-Class
Brand: Datamax Pages: 22
E+E Elektronik EE23 series Operation Manual preview
EE23 series
Brand: E+E Elektronik Pages: 20
Eaton TS110 Product Manual preview
TS110
Brand: Eaton Pages: 28
Parallel Galleon Installation Manual preview
Galleon
Brand: Parallel Pages: 16

Brands by name

Popular brands

Load more brands