Inficon UL5000 Technical Handbook Download Page 18

Page: 18 / 108

Installation

iina

e 0

chn

ica

l ha

boo

Installation

2.1

Transportation

UL5000 with Triscroll TS 620

For transportation the chassis plate where the pump is mounted on has to be
secured by a transportation fixing.

This transportation fixing consists of 2 screws at chassis of the UL5000 (one on each
side).

To get access to these screws remove the side covers of the UL5000.
There are orange labels on the bottom part pointing to the screws:

Caution

The UL5000 is not equipped with any crane eyes and must therefore not be
transported using lifting equipment.

Caution

The UL5000 must only be pushed along using the handle provided for this purpose.
Don’t use the handle to lift.

Caution

Your feet can be pinched.
Keep your feet away from the rollers. .

Caution

Your feet can be run over.
Do not pull the unit, push it.

Caution

When transporting over longer distances the original packaging must be used. The
castors must not be fixed when the UL5000 is shipped in a crate.

Summary of Contents for UL5000













































































































Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands

Inficon UL5000, Technical Handbook

Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands