Distance between the wall and the centre of the soil pipe: 451 - 580mm
2
Cutting the Drain Adjuster
Cut the drain adjuster for 100mm as shown in the
diagram on the right.
*If you make a longer cut on the adjuster, the toilet
bowl will be positioned closer to the wall. In that case,
interference may occur between the functioning parts
and the wall, which prevents the installation.
See NOTE 2.
06M038
アジャスター切断(d).eps
100mm
Bonding the Drain Adjuster with the Flange
3
Apply adhesive agent on the contacting parts of the
drain adjuster and the flange and connect them.
When connecting the drain socket with the adjuster,
fit the concave part with the convex part.
See NOTE 3.
See NOTE 4.
06M038
ソケット接着.eps
Drain Adjuster
Level Surface
Flange
Insertion
Margin
4
Fixing the Drain Adjuster and Flange
(1) Mount the gasket to the draining outlet of the
flange and fix them on the existing flange with
washers and flange nuts.
See NOTE 5.
See NOTE 6.
(2) Fix the drain socket with washers and the AY
bolts for fixing a toilet bowl.
Drill prepared holes (dia 11, depth 55) and use
the AY bolts.
Align the installation pattern paper with the rear end
of the drain adjuster and mark the C holes (mounting
holes for the mounting base) on the pattern paper.
Drill prepared holes (dia 11, depth 55) and use AY
bolts.
5
Fixing the Mounting Base
B
C穴
C穴
E穴
E穴
長さ合わせライ
ン
アジャスター部
固定部材側
壁側
壁側
固定部材側
長さ合わせライ
ン
アジャスター部
B穴
A穴
B
B
C
C
A
便器及び排水の仕様によりミシン目の折り位置が異なります。 施工説明書をご確認の上、正しく施工を行ってください。
壁側
壁側
Fixing Part
Washer
C Holes
AY Bolts for Anchoring the Toilet
6
to
フランジ部固定.eps
Existing Flange
Flange
Gasket
AY Bolts for Anchoring the Toilet
Washer
Flange Nut
Washer
Drain Adjuster
排水ソケットガスケット取付.eps
Gasket
Drain Outlet
Flange
When you fix the drain socket
on the floor, make sure that
the floor is not sloping or
uneven. If the drain adjuster
is fixed on an inverse slope,
it may cause flushing
malfunction or clogging.
When you fix the socket with
flange nuts, make sure not to
clench them too much.
Otherwise it may damage
the flange, which may cause
water leakage.
●
●
*
NOTE 6
If the existing bolts and
nuts, etc. on the flange are
corroded, use the T-bolts,
flange nuts, and washers
provided with the Satis.
●
NOTE 5
Never drop the drain
adjuster or flange on the
floor by mistake.
It may cause water leakage
from the damaged part.
After cutting the adjuster,
insert it into the flange
tentatively to see if the
adjuster length is correct.
Insufficient insertion will
cause the toilet installation
position to shift, resulting in
defective work.
Vertically cut the adjuster.
If it is cut askew, it may cause
water or odour leakage.
Do not leave burr on the
adjuster after cutting it.
It may case water or leakage.
●
*
●
*
●
*
●
*
NOTE 2
Make sure the adjuster and
flange are properly bonded.
Look in the bottom of the
flange and check if the adjuster
is thoroughly inserted.
If they are not adequately
bonded, it may cause water
or odour leakage.
●
*
NOTE 4
Gap
If you wrongly cut or bond
the adjuster, order the
following part number.
●
NOTE 3
CF-340SG-SET
