MDrive17Plus Microstepping Quick Reference Guide
The primary function of this guide is to acquaint the user with the spec i fi ca tions,
basic wiring and confi guration of the MDrive17Plus Mi crostep ping. The full prod uct
man u al and IMS SPI Motor Interface GUI (for quick and easy parameter setup) are
avail able on the IMS MDrive CD or may be down load ed from the IMS web site at
www.imshome.com.
The Product Manual also contains a "Getting Started" document to guide you in
rapidly setting up and turning your MDrive17Plus Microstepping.
Notes and Warnings
Please observe the following when handling, connecting and using your
MDrive17Plus. Failure to observe these points may result in damage to the product.
NOTE: The electronics are not removable from the motor in the fi eld. The entire unit
must be sent back to the factory for repair. All warranty and disclaimer information
are located in the full product manual and should be referenced for more information.
Additional Recommendations
Please reference the following in the product manual for detailed information on:
IMS SPI Motor Interface (GUI)......................................................... Section 2.4
Motor Performance Specifications.................................................... Appendix A
Recommended IMS Power Supplies ................................................. Appendix B
Recommended Wiring ..................................................................... Appendix B
IMS Cables and Cordsets................................................................ Appendix D
Optional Factory-Mounted Encoder .................................................. Appendix E
Layout and Interface Guide (Section 2.1)
Logic level cables must not run parallel to power cables. This will introduce noise and
make the system un re li able.
Logic level cables must be shielded to reduce the risk of EMI induced noise. The
shield must be grounded at the signal source to earth ground. The opposite end of the
shield must not be connected which allows it to fl oat and act as a drain.
The supply to the driver must be a twisted pair. If more than one driver is being con-
nected, run separate leads to each driver.
MDrive17Plus Versions Covered
The following MDrive17Plus Microstepping Drives are covered by this reference:
Connector Options P1:
Flying Lead, 7 Pin Terminal, 12 Pin Locking Wire Crimp*,
19 Pin M23 (Male)†
Connector Option P2 (SPI):
10-Pin IDC*
Connector Option P2 (SPI):
Connector Option P2 (SPI):
*The 12 Pin Locking Wire Crimp Eliminates P2
†
Sealed (-65)Versions Only
General Specifications (Part 1: Hardware Specifications)
Input Voltage (+V)*
Range .................................................................................... +12 to +48 VDC
*Max power supply current per MDrive17Plus: 2 Amps. Actual power supply
current will depend on voltage and load.
Isolated Input
Step Clock, Direction & Enable
Voltage Range (Sourcing or Sinking) .......................................... +5 to +24 VDC
Current
+5 Volt Max) ........................................................................................ 8.7 mA
+24 Volt (Max) ...................................................................................14.6 mA
Motion
Digital Filter Range ................................................................ 50 nS to 12.9 µS
Clock Types ............................. Step/Direction, Quadtrature, Step Up/Step Down
Step Frequency (Max)............................................................................ 2 MHz
Step Frequency Minimum Pulse Width ................................................... 250 nS
Number of Microstep Resolution Settings ...................................................... 20
��
TM
�������������
Securing MDrive17Plus Power and Encoder Leads
(Section 2.1)
Some applications may require that
the MDrive17Plus move with the axis
motion. If this is a requirement of your
ap pli ca tion, the motor leads and the
optional encoder leads (if equipped)
must be properly anchored. This will
prevent fl exing and tugging which can
cause damage at critical connection
points in the MDrive17 elec tron ics and
the Encoder. DO NOT bundle logic or
optional encoder leads with the MDrive
Power Leads.
�������
�����
������������
�����������������
���������
�����������
MDrive17Plus Mounting Holes/Screws (Section 2.1)
WARNING! The
mounting holes in
the MDrive17Plus
mounting fl ange
are not through holes.
The maximum length of
the screw threads into the
motor fl ange is 0.140” (3.5
mm).
NOTE! The maximum torque for the M3x0.5 screw is 7.8 lb-in (9 kg-cm)
with a thread engagement of 5 threads (3.3 mm deep). A lesser thread
engagement diminishes the maximum torque.
�����������������
������������������
�����������������
���������������
����������
���������������
��������������
����������
�����������
������������
Back EMF Warning
A char ac ter is tic of all motors is back EMF. Back
EMF is a source of current that can push the output
of a power supply beyond the maximum operat-
ing voltage of the driver. As a result, damage to the
stepper driver could occur over a period of time.
Care should be taken so that the back EMF does
not exceed the maximum input voltage rating of the
MDrive17Plus.
WARNING! The
m48 VDC
Input Voltage the
MDrive17Plus includes
Motor Back EMF, Power Supply
Ripple and High Line.
intelligent motion systems, inc.
Excellence in Motion
TM
370 N. MAIN ST., PO BOX 457, MARLBOROUGH, CT 06447
PH: (860) 295-6102, FAX: (860) 295-6107
Internet: www.imshome.com, E-Mail: [email protected]
QUICK REFERENCE
Available Microsteps Per Revolution
200
400
800
1000
1600
2000
3200
5000
6400
10000
12800
20000
25000
25600
40000
50000
21500
36000
1
21600
2
25400
3
1=0.01 deg/µstep 2=1 arc minute/µstep 3=0.001 mm/µstep
Sealing Specification (-65 Only)
Specification ............................................................................................ IP65
Thermal Specifications
The MDrivePlus consist of two core components, a drive and a motor. Close atten-
tion must be paid to the thermal environment where the device is used.
Operating Temperature ............................................................. -40° C to 85° C
Power and Logic Connections (Sections 2.1, 2.2)
+V
Power Ground
Opto Reference
Enable
Step Clock/CH A/Up
Direction/CH B/Dn
P1 - Function
Red
Black
White
Brown
Orange
Blue
Pin 7
Pin 6
Pin 1
Pin 5
Pin 3
Pin 4
Pin 2
Pin 1
Pin 3
Pin 5
Pin 4
Pin 6
Pin 6
Pin 19
Pin 1
Pin 2
Pin 18
Pin 13
12" Flying
Leads
19 Pin M23
(Male)
7 Pin
Pluggable
Terminal
12 Pin
Locking Wire
Crimp
MDrive17Plus
MDrive17Plus-65
SPI Communications Connections (Section 2.3)
+5 VDC Output
CGND
Pin 19
Pin 4
Pin 2
Pin 3
Pin 15
Chip Select
SPI Clock
Master In/Slave Out
Master Out/Slave In
Pin 6
Pin 5
Pin 4
Pin 8
Pin 10
Pin 7
Pin 7
Pin 9
Pin 11
Pin 8
Pin 10
Pin 12
Pin 10
Pin 11
Pin 9
Pin 16
Pin 17
Pin 8
P1: 23-Pin
M23 (Male)
P1: 12-Pin
Locking Wire
Crimp
P2: 10-Pin
IDC
PC Parallel
Port (DB-25)
MDrive17Plus
MDrive17Plus-65
Used with IMS Parameter Setup Cable Only - Not a User Output!
!
!
Plus
Plus-65
MDrive17Plus Microstepping Quick Reference - Revision R051106
