background image

3

Visit www.improvedracing.com for additional support

E5G-600-62 Hardware Pack Contents

Item Qty Part Number

Description

1

1

CP-16

Billet Aluminum Hose Separator

2

1

HSC-1052

Grade 5 Hex Head Screw, 

         

, L = 2-

3

/

4

 inch

3

2

HWA-1004

1

/

4

 inch Washer

E5G-600-64 Hardware Pack Contents

Item Qty Part Number

Description

1

1

HSC-1051

8.8 Class Alloy Steel M8x1.25x35 Screw

2

1

HWA-1005

M8 Zinc-Plated Steel Fender Washer

3

1

HNT-1018

M8x1.25 IFI Prevailing Torque Nut

4

2

HTD-1004

M8 Stud-Mount, High-Temperature Cable-Tie

E5G-680 Hardware Pack Contents

Item Qty Part Number

Description

1

1

22962571

2010-2011 V8 Camaro Upper Radiator Hose

2

1

12561663

LSX / Vortec Engine Block Coolant Plug

TECHNICAL SPECIFICATIONS

Maximum Operating 

Temperature

302°F (150°C)

Minimum Operating 

Temperature

-22°F (-30°C)

Maximum Operating 

Pressure

300 psi (20.68 bar)

Heat Exchanger 

Material & Fabrication

45-Row Full Aluminum Tube & Fin Core with Turbulators, TIG 

Welded Tanks, Billet CNC-Machined End Caps & Fittings

Adapter Fitting 

Material & Fabrication

CNC-Machined 6061-T6 Aluminum, MIL-A-8625 Type II 

Black-Anodize

HCP-1016 Info

1-1/2 inch (38 mm) ID P-Clamp, Zinc-Plated Steel, Black EPDM 

Rubber , 210°F (99°C) Max Temp

22962571 Info

Genuine GM  2010-2011 Chevrolet Camaro V8 Upper Radiator 

Hose, Rubber, Black

12561663 Info

Genuine GM LS / Vortec Family Engine Coolant Plug, 17 mm 

Hexagon Drive, Yellow Brass, Thread-Lock Applied

E5G-600-50 Info

-10 Hose Assembly: 90° & 90° 6061-T6 Aluminum Hose-Ends, 

ECO Rubber Outside Bonded to Viton Rubber Inside, Stainless 

Steel Reinforced, Nylon Over-Braid, Fiberglass-Silicone Shield

Summary of Contents for E5G-600


















Reviews: