background image

Laser Diode Driver LD8000 

18 

Ver. 1.0 

6. Warranty 

 

Impex HighTech

 LD8000 is warranted to be free of defects in material and workmanship for 12 

month  from  date  of  shipment.  The  warranty  shall  not  cover  any  damage  incurred  during 
shipping. When the product is received by the customers, the shipping container and its content 
should  be  inspected  for  any  damage  incurred  during  shipping.  In  order  to  obtain  service  under 
this warranty, the customer must notify 

Impex HighTech

 about the defect before the expiration 

of  the  warranty  period  and  make  suitable  arrangements  for  the  performance  of  service.  In  all 
cases  the  customer  will  be  responsible  for  properly  packing  and  shipping  the  product  back  to 

Impex HighTech

, with shipping charges prepaid. If the product is not properly packed, it will be 

damaged in shipping and the warranty will be avoided. 
This warranty shall not apply to any defect, failure, or damage caused by improper use, failure to 
observe  proper  operating  procedures  per  the  product  specifications  (see  chapter  2. 
Specifications), or improper/inadequate maintenance. 

Impex HighTech

 shall not be obligated to 

furnish  service  under  this  warranty  1)  to  repair  damage  resulting  from  attempts  by  personnel 
(other  than 

Impex  HighTech

  representatives)  to  repair  or  service  the  product;  2)  to  repair 

damage  resulting  from  improper  use  or  connection  to  incompatible  equipment;  3)  to  repair 
damage  resulting  from  operation  outside  of  the  operating  environmental  specifications  of  the 
product; 4) to repair damage resulting from improper packaging of the product in order to return 
it to 

Impex HighTech

Version 1.0 

20. November 2008 

 

IMPEX HighTech GmbH

 

Hovesaatstr. 6 

48432 Rheine 

Germany 

Phone: +49(0)5971 981 650 

FAX: +49(0)5971 981 659 

Summary of Contents for LD8000



















Reviews: