background image

EC DECLARATION OF CONFORMITY

4HE MANUFACTURER OF THE PRODUCT COVERED BY THIS $ECLARATION IS

.!0 "RANDS ,TD
.APIER (OUSE 5NIT  #ORUNNA #OURT
7ARWICK INGDOM #6 (1

4HE MANUFACTURER HEREBY DECLARES THAT THE MACHINE AS DETAILED IN THIS DECLARATION FULFILS ALL THE
RELEVANT PROVISIONS OF THE -ACHINERY $IRECTIVE AND OTHER APPROPRIATE DIRECTIVES AS DETAILED BELOW

4HE MANUFACTURE FURTHER DECLARES THAT THE MACHINE AS DETAILED IN THIS DECLARATION WHERE APPLICABLE
FULFILS THE RELEVANT PROVISIONS OF THE ESSENTIAL HEALTH AND SAFETY REQUIREMENTS

4HE $IRECTIVES COVERED BY THIS $ECLARATION ARE AS DETAILED BELOW

0RODUCT $ETAILS
$ESCRIPTION , /IL,UBRICATED !IR #OMPRESSOR
-ODEL .O )-,
"RAND .AME )MPAX

.AME AND ADDRESS OF TECHNICAL DOCUMENTATION HOLDER
4HE TECHNICAL DOCUMENTATION REQUIRED TO DEMONSTRATE THAT THE PRODUCT MEETS THE REQUIREMENTS OF
DIRECTIVE HAS BEEN COMPILED AND IS AVAILABLE FOR INSPECTION BY THE RELEVANT ENFORCEMENT AUTHORITIES

3IGNED

0RINT -ARK 3HANNON

1UALITY $IRECTOR
.!0 "RANDS ,TD
.APIER (OUSE 5NIT  #ORUNNA #OURT 7ARWICK INGDOM #6 (1

$ATE

%# 4HE -ACHINERY $IRECTIVE
%# ,OW 6OLTAGE %QUIPMENT $IRECTIVE
%# %LECTROMAGNETIC #OMPATIBILITY $IRECTIVE
%# 4HE #% -ARKING $IRECTIVE
%5 4HE 2ESTRICTION OF THE 5SE OF CERTAIN (AZARDOUS 3UBSTANCES IN %LECTRICAL %QUIPMENT
2O(3  $IRECTIVE
%# AS AMENDED BY %# 4HE 7ASTE %LECTRICAL AND %LECTRONIC %QUIPMENT 7%%% 
$IRECTIVE
%# !NNEX 6) AND THE $IRECTIVE %# 4HE .OISE %MISSIONS IN THE %NVIRONMENT BY
%QUIPMENT FOR USE /UTDOORS 2EGULATIONS  3)  AS AMENDED 

!FTER SALES SUPPORT 4EL    7EBSITE WWWIMPAXPOWERTOOLSCOM

14

!ND IS IN CONFORMITY WITH THE APPLICABLE REQUIREMENTS OF THE FOLLOWING DOCUMENTS

%. 
%. 
%. 
%. 
%. 
%. 

Summary of Contents for IM412-24L

















Reviews: