background image

Bambino 

 

11 

Troubleshooting

 

Problem: No signal at all 

 

Make sure the camera and the computer are turned on. 

 

Make sure the power plugs are pushed all the way in. 

 

If the camera is powered by batteries, replace all batteries with new 

ones. 

Problem: The signal is poor, or there is interference 

 

Make sure the camera and USB receiver are within range of each other, 

maximum 450 feet (150 meters) approximately, if in clear line of sight. 

Safety Information 

 

Keep all parts and accessories out of children's reach. 

Fingerprints or dirt on the lens surface can adversely affect camera performance. 

Avoid touching the lens surface with your fingers. 

Should the lens become dirty, use a blower to blow off dirt and dust, or a soft, 
dry cloth to wipe off the lens. 

Keep the camera dry. Precipitation, humidity, and other liquids containing 
minerals will corrode electronic circuits. 

Do not use or store in dusty, dirty areas. 

Do not store in hot areas. High temperatures can shorten the life of electronic 

devices and warp or melt certain plastics. 

Do not store in very cold areas. When the camera is turned on and warms up, 

moisture can form inside the casing and may damage electronic circuit boards. 

Use only the supplied AC power adapter to power the camera. 

Do not overload electrical outlets or extension cords as this can result in fire or 

electric shocks. 

Avoid dropping or subjecting the device to strong shocks. 

Do not attempt to open, dismantle, repair, or service the camera. Doing so may 

cause electric shocks and other hazards. 

Any evidence of misuse, abuse, or tampering will void the Limited Warranty. 

 

For More Information

 

 

To get updates or to learn more about ImogenStudio products, please visit 

www.imogenstudio.com

 

Summary of Contents for Bambino












Reviews: