8
English
Deutsch
Deutsch Seite
Français
Français Page
Italiano
Italiano Pagina
Español
Español Página
Nederlands
Nederlands Pagina
Polski
Polski Strona
English
English Page
Wireless hand-held microphone
These instructions are intended for users without
any specific technical knowledge . Please read these
instructions carefully prior to operating the unit and
keep them for later reference .
All operating elements and connections de-
scribed can be found on the fold-out page 3 .
1 Overview
1
Display to indicate
1 . the channel group (GROUP 00 – 07)
2 . the channel (CHANNEL 00 – 99)
3 . the microphone sensitivity
(VOL −30 dB, −20 dB, −10 dB, 00 dB)
4 . the battery status
BATT
■
■
■
■
■
BATT
■
■
■
BATT
full half-full discharged
2
On / off switch
3
Screw sleeve
To access the operating elements (5) to (7) and
the battery compartment on the rear side, un-
screw the sleeve .
4
Threaded ring for the screw sleeve (3)
5
Buttons
and
to set the channel group, the
channel number and the microphone sensitivity
6
Button SET: To change the channel group, the
channel number or the microphone sensitivity,
press the button SET repeatedly until the corre-
sponding numerals start flashing on the display
(1) . While the numerals keep flashing, make the
settings with the buttons
and
.
7
Switch RF for the transmission power
position L: low transmission power (2 .5 mW)
position H: high transmission power (25 mW)
8
Sensor for the IR signals for automatic channel
setting
2 Important Notes
The wireless microphone corresponds to all relevant
directives of the EU and is therefore marked with .
•
The microphone is suitable for indoor use only .
Protect it against dripping water and splash
water, high air humidity and heat (admissible
ambient temperature range 0 – 40 °C) .
•
For cleaning only use a dry, soft cloth; never use
water or chemicals .
•
No guarantee claims for the microphone and
no liability for any resulting personal damage or
material damage will be accepted if the micro-
phone is used for other purposes than originally
intended, if it is not correctly operated, or if it is
not repaired in an expert way .
If the microphone is to be put out of oper-
ation definitively, take it to a local recycling
plant for a disposal which is not harmful to
the environment .
3 Applications
To provide a wireless audio transmission system,
combine this dynamic hand-held microphone with
integrated multi-frequency transmitter with the
following receivers from IMG STAGELINE:
TXS-606 with 1 receiver unit
TXS-626 with 2 receiver units
TXS-646 with 4 receiver units
TXS-686 with 8 receiver units
The transmission frequency within the UHF
range 672 .000 – 691 .975 MHz is freely selectable
(frequency spacing 25 kHz) .
Due to the ACT function (automatic channel
targeting), the audio transmission system is very
easy to operate: Simply press a button and, via IR
signal, the wireless microphone is set to the chan-
nel selected on the receiver .
3.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare that
the wireless microphone TXS-606HT complies with
the directive 2014 / 53 / EU . The EU declaration of
conformity is available on the Internet:
www .img-stageline .com
Restrictions or requirements apply in the fol-
lowing countries:
CZ
DE
EL
FI
FR
IT
LT
MT
PL
In the Federal Republic of Germany, the wireless
microphone requires a frequency assignment (for
which a fee is charged) .
In other countries, it is necessary to apply for a cor-
responding approval . Prior to operating the wire-
less microphone outside Germany, please contact
the MONACOR subsidiary or the corresponding
authorities of the respective country . Links to the
national authorities can be found via the following
Internet address:
www .cept .org
t
ECC
t
Topics
t
Other spectrum topics: SRD Regulations and
indicative list of equipment sub-classes
t
EFIS and National Frequency Tables
