background image

A. The

filters

can be removed for cleaning or replace-

ment (see CHECKING AND CLEANING THE FIL-
TERS on page 13).

B. The 

underwater light

can be used for night opera-

tion (see USING THE CONTROLS on page 12). The
spa includes both red and blue covers for the light.

C. The 

temperature probe 

monitors water temperature.

D. The 

volcano jet

provides a soothing foot massage. 

E. The 

cloudburst jet

diverts the water flow three dif-

ferent ways. By turning the outer ring, you can divert
the water flow between the volcano jet (D), the other
jets on the spa, and the cloudburst jet (E), which cre-
ates a whirlpool action. 

Note: The outer ring may

be hard to turn while the pump is turned on high.

F. The 

four suction fittings

provide water to the

pumps. The suction covers should always be in
place over the fittings. Never operate the spa with-
out the suction covers in place.

G. An optional ozone generator can be purchased and

installed to utilize the 

ozone jet

. Ozone helps sani-

tize the spa with minimal chemical treatment.

H. The

console

controls the spa jets, turns the under-

water light on and off, and adjusts the water tem-

perature setting (see USING THE CONTROLS on
page 12).

I. The 

four air controls

regulate the air flow to the

whirlpool, hydrotherapy, and volcano jets.

J. The 

two neck jets

can be adjusted to spray sooth-

ing water on your neck. To activate the neck jets,
turn the on/off valve (P) counterclockwise. To turn
the neck jets off, turn the on/off valve clockwise.

K. The 

twenty

-

one rotary jets

provide a spinning mas-

sage.

L. The 

dual rotary jets

provide a pulsating massage

action. Rotate the outer ring counterclockwise to
turn the jets on. Rotate the outer ring clockwise to
turn the jets off.

M. The 

three variable-flow jets

are fully adjustable.

Turn the outer rings to regulate the flow.

N. The 

power massage jet

provides a soothing mas-

sage to your lower back. Turn the outer ring to reg-
ulate the flow.

O. The 

skimmer

cleans the surface of the water.

P. The 

on/off valve

controls water flow to the two neck

jets (J). To completely turn off the water flow to the
jets, see PUMP BUTTON 2 on page 12.

11

Spa Shell Diagram

A

O

L

B

D

I

E

I

H

F

M

M

M

P

J

J

L

L

L

L

K

K

K

K

K

K

K

G

C

N

L

L

Summary of Contents for IMSW73910





















Reviews: