© Copyright 2020, ILUMINAR Lighting
Subject to change without notice.
5
4
1-877-540-5588
iluminarlighting.com
PLEASE READ CAREFULLY PRIOR TO INSTALLATION
INSTALLATION
PROCEDURE
When possible, have a licensed electrician or electrical expert install all
fixtures or aid in the electrical layout plans and/or diagrams prior to
installation.
Check the electrical panel to ensure proper voltage is available for the
number of fixtures installed. Panels should only support a total amperage
of 80% of its capacity. (100 amp panel should never exceed 80 amps).
1. Find a suitable location for the fixture with sufficient cooling and away
from heat sources.
2. Use the included hanging cables to hang the fixture.
3. Ensure the fixture is hung completely level to the ground. A fixture that
is not level can burn the lamp emitter incorrectly leading to shorter
lamp life, poor lamp performance and/or lamp failures.
4. Install the lamp into the roll-lock socket (instructions pages 6-7) using
soft cotton or surgical gloves.
5. Plug the power cord into the power source (electrical outlet).
6. For proper lamp break-in, we recommend that you run the fixture at
100% power for at least 100 straight hours after initial startup. This
will improve lamp life and performance.
7. Set your desired dimming ratio. NOTE: the ballast dims or raises
output gradually to protect the lamp, so you may not see an instant
increase upon changing your output percentage.
•
Turn the dimming dial to cycle through the dimming levels.
•
If your lamp fails to start immediately, DO NOT cycle the power on
and off. This can damage the lamp and ballast.
•
If after 30 minutes your lamp is still not lit, shut off power to the
ballast, and reconnect.
•
This will begin the startup sequence again.
•
Until the lamp has achieved at least 100 hours of operation, the lamp
should never be turned off prior to running at least 15 minutes. In
case this happens, WAIT 1 hour before igniting the lamp again.
IT IS VERY IMPORTANT
that the lamp is given adequate time to cool
down before it is reignited. Allow a hot lamp to cool for 1 hour before
you try to restrike it. Hot re-strikes cause permanent lamp failure and
lumen output degradations. The lamp should never be turned off before
the lamp reaches full intensity, this may shorten its lifespan.
DO NOT
install fixtures in areas of high heat, such as an attic, tent or
closed closet. Mount units at least 24-60 inches apart.
1. End of Lamp Life (EOL) Protection
2. Short Circuit Protection
3. Open Circuit Protection
4. Ignition Failure Protection
5. Thermal Protection
6. Suitable for ILUMINAR Touch Controller & HASH Controller
7. Suitable for HASH Controller / 0-10V Control
8. Total Control Range 50-115%
RATED MAINS VOLTAGE
120V
240V
277V
347V
VOLTAGE RANGE +/- 10%
108-264V
249-305V 312-382V
INPUT FREQUENCY
48 - 63Hz
PERFORMANCE
REQUIREMENTS
WIRING
DIAGRAM
DIMMING
CASE LENGTH
249mm
9.80”
CASE WIDTH
249mm
9.80”
HEIGHT
609mm
23.98”
WEIGHT
6.2kg
13.66 lbs
PHYSICAL
SPECIFICATIONS
1. Max. allowable case temperature: 75º C / 167º F
2. Ambient Temperature: -20º to +40º C / -4 to +104º F
3. Max. Humidity: 95%
4. Ignition Voltage: 5kV
CARE
HOT RESTRIKE
MOUNTING
LOCATION
BALLAST
PROTECTIONS
COMPATIBILITY
Compatible with all ILUMINAR MH DE lamps & HPS DE lamps as well as
the ILUMINAR Touch & ILUMINAR HASH Environment controllers.
RJ14 Controller Connection
Wieland Female
Wieland Male
120V SKU CORD: IL-WLDCRD-120V
240V SKU CORD: IL-WLDCRD-240V
277V SKU CORD: IL-WLDCRD-277V
347V SKU CORD:IL-WLDCRD-347V
5m
