Ikra HS 6070 Pro Operating Instructions Manual Download Page 17

GB

 | 

Operating Instruction

4

the tool with your finger on the on/off switch or con

-

necting the tool to the mains supply with the switch 

in ‘ON’ position, this may result in accidents.

d) Remove adjustment tools or wrenches and the 

like before you switch the tool on.

 

A wrench or 

another tool that is inside or on a turning part of the 

tool may cause injury.

e) Do not overestimate your abilities. Take care 

of a safe footing and keep your balance at all 

times.

 

This will allow you to better control the tool 

in unexpected situations.

f)  Wear suitable clothes. Do not wear wide cloth-

ing  or  jewellery.  Keep  your  hair,  clothes  and 

gloves clear of all moving parts. 

Loose clothing, 

jewellery or long hair may get caught in moving 

parts.

g) 

If  dust  extraction/collection  devices  are  pro

-

vided make sure that they are connected and 

used properly.

 

The use of these devices reduces 

hazards caused by dust.

4) Careful handling and use of power tools

a) Do not overtax the power tool. Use the power 

tool intended for your type of work in each 

case.

 

The use of the suitable power tool within the 

stated range of performance makes working more 

effective and safer.

b) Do not use a power tool with a damaged switch.

 

A power tool that cannot be switched on or off any 

more is dangerous and must be repaired.

c) Pull the mains plug out of the socket before 

you  adjust  a  tool,  change  accessories  or  put 

the tool aside.

 

This precaution avoids the uninten-

tional start of the tool.

d) Store power tools out of the reach of children. 

Do not allow persons to use the tool if they are 

not familiar with the tool or these instructions. 

Power tools are dangerous if used by inexperi-

enced persons.

e) Thoroughly maintain your power tool. Check 

whether moving parts are working properly 

and  are  not  jamming/sticking,  and  whether 

parts are broken or otherwise damaged in a 

way that affects the function of the tool. Have 

damaged parts repaired before using the tool.

 

Many accidents are the result of poorly maintained 

power tools.

f)  Keep cutting tools sharp and clean.

 

Thoroughly 

looked-after cutting tools with sharp cutting edges 

are jamming less often and are easier to guide.

g) 

Use  power  tools,  accessories,  add-on  tools, 

etc. in accordance with these instructions and 

in the way prescribed for the respective type 

of tool.  You should also consider the working 

conditions and the work to be carried out.

 

The 

use of power tools for purposes other than those 

intended for the respective tool may result in dan-

gerous situations.

5) Service

a) 

Have the power tool serviced by qualified tech

-

nical personnel only; repairs should be carried 

out using exclusively original spare parts.

 

This 

will ensure the safe operation of the power tool.

Safety instructions for hedge trimmers:

Keep all parts of your body away from the cutting 

blades. Do not try to remove cut-off matter with 

the tool running. Do not try to hold material to be 

cut off with your hand. Remove cut-off matter that 

is stuck between the blades only with the tool be-

ing switched off!

 

When working with hedge trimmers 

even a short moment of inattentiveness may result in 

severe injury.

Hold the power tool by its insulated handling sur-

faces as the cutting blades might get in touch with 

the tool’s own power cable. 

If the cutting blades 

should accidentally cut into a live power cable this 

might turn metal parts of the tool ‘hot’ thereby causing 

an electric shock.

Carry the hedge trimmer at the handle with the 

cutting blades standing still. Always put on the 

protection cover when transporting or storing the 

hedge trimmer.

 

Careful handling reduces the risk of 

injury through the cutting blades. 

Keep the cable away from the cutting area. 

When 

working with the trimmer the cable might be hidden in 

bushes and accidentally cut through.

 

-

The hedge trimmer should always be held with 

both hands. 

 

-

Before using the equipment clear the working 

area of any foreign objects and be aware of for-

eign objects during operation of the machine! 

 

-

Do not use the trimmer in wet weather  and do 

not use it to cut wet hedges.Do not wash down 

the device with water. Do not use any high-

pressure cleaning devices or steam jet devices 

for cleaning.

 

-

In line with agricultural Trade Association Regula-

tions only persons over the age of 17 may work 

on their own with electric hedge trimmers. Use is 

permitted for persons over 16 years if the work is 

carried out under the supervision of adults. 

 

-

Equipment which will be used in different outside 

locations should be connected via residual cur-

rent - operated current breakers. 

 

-

For initial use of the hedge trimmer we would rec-

ommend that in addition to reading the operating 

instructions, you also seek a practical demonstra

-

tion from an expert. 

 

-

Always ensure that all protective devices and 

handles are properly fitted. Never attempt to use 

an incomplete machine.

 

-

Never  try to use an incomplete tool or a tool that 

has  been  modified  in  a  way  that  has  not  been 

approved. 

 

-

Familiarize yourself with the working area and pay 

attention to possible dangers which you might not 

be able to hear due to the noise of the machine. 

Summary of Contents for HS 6070 Pro

























































Reviews: