Ikon IK23 Installation And User Manual Download Page 20

12/12/2018

20

10 

REPLACING THE LAMPS

Contact the dealer or customer service when the lamp of the appli-

ance fails ()

REPLACING THE LAMPS

 

07.02.2019

4260 HOOD USER GUIDE

26

11 

AUTHORIZED SERVICE

n

Make sure that the plug is plugged in, and that the fuses are

intact.

n

Check the bulbs. Make sure you unplugged the device before

performing this check. Tighten the bulbs if they are loose; you

can replace the bulbs if they still don't work.

n

Check to see if the hood is plugged in or if the plug is fit prop-

erly into the socket.

n

Check the fuse, to which the appliance is connected, as well as

the main fuse of your house.

n

Is the outlet diameter of the appliance's flue adequate? (min.

120 mm).

n

Are the metal filters clean? Please check.

n

If you use the hood without flue, make sure that the carbon fil-

ters are not older than 6 months.

n

Be attentive to ventilate your kitchen adequately, in order to

provide an airflow. If you are still not satisfied with the perform-

ance of the appliance, consult the authorized technical service.

Fault description

Cause

Remedy

Product Does Not Work

Check the power

connection.

Mains voltage must be 220-240 V, and product

must be plugged into a grounded socket.

Illumination lamp does not

operate

Check the power

connection.

Mains voltage must be 220-240 V, and product

must be plugged into a grounded socket.

Illumination lamp does not

operate

Check the lamp

switch.

Lamp switch must be at "on" position.

Illumination lamp does not

operate

Check the bulbs.

Bulbs must be operative.

Product's Air Intake is Weak

Check The Alumi-

nium Filter.

The aluminium cartridge filter should be washed

once a month under normal conditions.

Product's Air Intake is Weak

Check The Air Outlet

Flue.

Air Outlet Flue Must Be Open.

Product's Air Intake is Weak

Check The Carbon

Filter.

In products that work with carbon filters, carbon

filter must be replaced once in every 3 months

under normal conditions.

If Lighting is Not Functioning:

Possible Faults and Things that

You can do Before Calling Tech-

nical Service:
A) If the device does not run in any

way:

If the device performance is not

enough and it creates high noise

while running:

Troubleshooting

AUTHORIZED SERVICE

 

07.02.2019

4260 HOOD USER GUIDE

27

Summary of Contents for IK23






















Reviews: