IKER ZBS-20A Instruction Manual Download Page 7

 

 

Caring 

1.Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently. When   

    cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to   

    clean the inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or   

    diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.   

2.Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction.     

    Do not use mechanical devices or other means to accelerate the defrosting process, other than those   

    recommended by the manufacturer. 

3.To ensure the cleanliness of the ice cubes, water in the water reservoir  is suggested to be replaced 

every 24 hours.   

5.If the compressor stops for any reason such as water shortage, too much Ice, power off, etc... Do not   

    start the system right away, wait 3 minutes, and then re-start the Ice maker.   

6.Always use fresh water before starting ice production either at initial installation or after a long shut-off   

    period.   

7.This unit is for home use only,not for outdoor use,if it is necessary for use outside,please make sure   

    the view window is closed. 

 

Safety Notice 

In order to avoid any accidents, please refer to following operation: 

1. Disconnect power before servicing. 

2. Do not pull directly on wire when plugging or unplugging the unit. 

3. If ice is abnormal, please call the seller. 

4. It is normal for the compressor and condenser surface to reach temperatures between 70°C and 90°C 

during operation and surrounding areas may be hot. Please don't touch it. 

5. Due to fast freezing, ice cubes m

ay appear “Cloudy”. This is trapped air in the water and it will not 

affect quality or taste of ice. 

6.  When  out  of  use,  please  open  the  drawer  at  least  2cm  to  allow  for  air  circulation  and  avoid  any 

metallic components becoming rusted. 

7. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a 

similarly qualified person in order to avoid a hazard. 

8.  This  appliance  can  be  used  by  children  aged  from  8years  and  above  and  persons  with  reduced 

physical, sensory  or mental capabilities or lack  of experience and knowledge  if they have been given 

supervision  or  instruction  concerning  use  of  the  appliance  in  a  safe way  and  understand  the  hazards 

involved. 

9.Children shall not play with the appliance. 

Cleaning and user maintenance shall not be made by children without supervision 

10. WARNING: fill with bottled or good quality tap water only.    (Do not fill with fruit juices or other drink 

types). 

11. WARNING 

– Keep the air vents on the sides of the machine unblocked at all times. 

12. WARNING 

– Do not use mechanical devices or other means to accelerate the defrosting process, 

other than those recommended by the manufacturer. 

13. WARNING 

– Do not damage the refrigerant circuit. 

Summary of Contents for ZBS-20A









Reviews: