background image

4

Safety instructions

Working with the device:

Do not use the device in explosive 
atmospheres, it is not EX-protected. 

With substances capable of forming an explosive mixture, 
appropriate safety measures must be applied, e.g. work-
ing under a fume hood.

To avoid body injury and property damage, observe the 
relevant safety and accident prevention measures when 
processing hazardous materials.

Only process media that will not react dangerously to the 
extra energy produced through processing. This also ap-
plies to any extra energy produced in other ways, e.g. 
through light irradiation.

The device is not suitable for hand-held operation.

Switch off the device at the power switch (item 8) or pull 
out the mains plug when changing or handling the dis-
persing tool.

Do not touch rotating parts during 
operation!

The dispersing tool and the cou-
pling flange can become hot during 
the operation. 

If a dispersion tool is not inserted into the drive flange as 
far as the mark it can become extremely hot in operation 
and thus suffer damage.

Be aware that the unit starts with the 
set speed, which is shown on the dis-
play. If uncertain start with the lowest 

speed and increase it gradually.

Reduce the speed if the medium splashes out of the vessel 
because the speed is too high.

If the interaction between the medium and dispersing 
element or working with dispersing tools with a stator 
diameter ≥18 mm and a speed of more than 20000 rpm, 
makes a loud noise, be sure to wear your personal protec-
tive equipment.

General information:

• 

Read the operating instructions in full before start-

ing up and follow the safety instructions.

• Keep the operating instructions in a place where they can 

be accessed by everyone.

• Ensure that only trained staff work with the device.
• Follow the safety instructions, guidelines, occupational 

health and safety and accident prevention regulations.

Please pay attention to the danger-
ous parts of the equipment in Fig. 2.

Beware of the risk of:
- flammable materials
- glass breakage
- sharp edges on the dispersing tool. 

Wear your personal protective 
equipment in accordance with the 
hazard category of the media to be 

processed. There is a risk from:
- splashing and evaporation of liquids
- body parts, hair, clothing and jewellery getting caught.

• The device must only be used in a technically perfect condition.
• Do not cover the ventilation slots on the drive in order to 

ensure adequate cooling of the drive.

• The voltage stated on the type plate must correspond to 

the power voltage.

• Abrasion of the dispersion equipment or the rotating ac-

cessories can get into the medium you are working on.

Device setup:

The power switch of the IKA device 
must be accessed immediately, di-
rectly and without risk at any time. 

If access to the power switch cannot be ensured, an addi-
tional emergency stop switch that can be easily accessed 
must be installed in the work area.

Make sure that the unit is stably 
mounted. The vessel used for dis-
persing must be secured.

Set up the stand in a spacious area 
on an even, stable, clean, non-slip, 
dry and fireproof surface.

• Ensure that the dispersion tool is securely properly into 

the drive unit.

• All screw connections must be properly tightened.
• Check that the turning knobs are secure and tighten if 

necessary.

• Glass vessels must always be secured with a clamp to pre-

vent them spinning. 

DANGER

CAUTION

DANGER

WARNING

NOTICE

WARNING

WARNING

• Before switching on the dispersing device make sure that 

the dispersion tool shaft is immersed in the medium. Ob-
serve the operating instructions of the dispersion tools.

• The distance between the dispersion tool and the vessel 

bottom should not be less than 10 mm

.

• Use the dispersion tool always inside the dispersing vessel.
• Do not use the device without a dispersion tool.

DANGER

CAUTION

Summary of Contents for T25 easy clean digital


















Reviews: