12
extractor hood. Please contact
IKA
®
if you have any questions.
•
Do not
operate the appliance in explosive atmospheres, with
hazardous substances or under water.
• Please observe the operating instructions for any accessories used.
• The socket for the mains cord must be easily accessible.
• Ensure that the external temperature sensor PT 1000 is inserted in
the media to a depth of at least 20 mm.
• The external temperature sensor PT 1000 must always be inserted
in the media when connected.
• The appliance can only be disconnected from the mains supply by
pulling out the mains plug or the connector plug.
• Safe operation is only guaranteed with the accessories described
in the ”Accessories” chapter.
• Always disconnect the plug before fitting accessories.
• Accessories must be securely attached to the device and cannot
come off by themselves. The center of gravity of the assembly
must lie within the set-up surface.
• The appliance starts up again automatically following a cut in the
power supply (in operating mode B / C).
• The appliance may heat up when in use.
• Abrasion of the dispersion equipment or the rotating accessories
can get into the medium you are working on.
• When using PTFE-coated magnetic bars, the following has to be
noted:
Chemical reactions of PTFE occur in contact with molten or
dissolved alkaline and alkaline - earth metals, as well as with fine-
particled powders of metals of the 2. and 3. group of the periodi-
cal system at temperatures above 300-400 °C. Only elementary
fluorine, chlorine trifluoride und alkaline metals do attack PTFE,
halogen hydrocarbons have a reversibly swelling effect.
Source: Römpps Chemie-Lexikon and “Ullmann“ Bd.19
To the protection of the equipment
• The appliance may only be opened by experts.
• The voltage stated on the nameplate must correspond to the
mains voltage.
• Do not cover the device, even partially e.g. with metallic plates or
film. This results in overheating.
• Protect the appliance and accessories from bumps and impacts.
• Ensure that the base plate is kept clean.
• Observe the minimum distances between devices, between the
device and the wall and above the assembly (min. 800 mm).
•
Unpack
- Please unpack the device carefully
- In the case of any damage a fact report must be set
immediately (post, rail or forwarder)
•
Delivery scope
- Heating magnetic stirrer
- PT 1000
- Mains cable
- Operating instructions
•
Use
-
For mixing and/or heating liquids
•
Range of use
- Laboratories - Schools - Pharmacies
This device is suitable for use in all areas except:
- Residential areas
- Areas that are connected directly to a low-voltage supply network that
also supplies residential areas.
The safety of the user cannot be guaranteed if the appliance is ope-
rated with accessories that are not supplied or recommended by the
manufacturer or if the appliance is operated improperly contrary to the
manufacturer’s specifications.
Unpack
Correct use
Summary of Contents for C-MAG HS 10
