IHP ODLVF36ZEN Assembly, Installation And Operation Instructions Download Page 8

Page: 8 / 42

IHP.us.com

900861-00D

SINGLE-SIDED FIREPLACE

DIMENSIONS, FRAMING

AND CLEARANCES SECTION

This fireplace comes with various boxes prepackaged inside the fireplace. Do not discard any boxes unless

notes to do so. Read the list below for the contents.

Component Parts Box Contents:

(1) RGB Control Assembly (includes switches and LED dimmer)

(1) 12VCD Adaptor (used for LED lighting)

(1) 7.5VCD Adaptor (used for valve system)

(2) 6x12 Stainless Steel Vents (used to ventilate enclosure)

(12) Black Screws, Nuts & Washers for 6x12 vents

(1) Installation manual for vent kit

(1) 24-inch LED wire harness

(1) 10-foot valve system (module) wire harness

(1) LED 10-foot controller wire harness

(1) Manual shut-off gas valve

(1) Pilot Hood

(1) OFP Pilot Screen

(1) Dielectric Grease (for electronic connections)

Windshield Parts Box Contents:

(4) Glass Windshields (inside firebox)

(8) Glass Windshield Supports (4 for singled-sided; 8 for see-through fireplace)

(2) Stainless Steel Hoods (1 for singled-sided; 2 for see-through fireplace)

(14) Stainless Machine Screws (For hood install - depending on size, all may not be used)

(1) LED Tray Assembly Left

(1) LED Tray Assembly Right

Glass Media Box Contents:

(3-5) bags of diamond crystal media depending on model size

(See Table 7 and Figures 35 & 36 on Pages 24 & 25 for reference)

NOTE: Preparation for the LED lighting and the inlet gas line must be

planned before the fireplace is installed. See

Page 5, Figure 1

for inlet

gasline and

Page 15

for LED lighting.

SINGLE-SIDED FIREPLACE DIMENSIONS AND CLEARANCES

Summary of Contents for ODLVF36ZEN











































Search results

Summary of Contents for ODLVF36ZEN

Reviews:

Related manuals for ODLVF36ZEN

Brands by name

Popular brands

IHP ODLVF36ZEN, Assembly, Installation And Operation Instructions

Search results

Summary of Contents for ODLVF36ZEN

Reviews:

Related manuals for ODLVF36ZEN

Brands by name

Popular brands