background image

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

4

~

Refl ector

Fireplace 
Front

Tab

Rear Ledge

Install side panels (from required fi rebox liner kit)

1. 

Align the screw hole in the top fl ange of the side panel with 
the upper hole in the inside wall of the fi replace 

(

Figure 8

).

2. 

Align the screw holes in the bottom fl anges of the side 
panel with the holes in the front and rear ledges.

3. 

Secure each panel with three (3) #10-16 x 3/8 hex-head 
sheet metal screws provided with the fi rebox liner kit.

Left Side 
Panel

Right 
Side 
Panel

~

Left Side
Panel

Front
Ledge

Rear
Ledge

~

Install back panel (from required fi rebox panel kit)

1. 

Insert the bottom edge of the back panel into the fi replace 
fi rst, then position it in front of the previously installed 
refl ector 

(

Figure 9

)

.

NOTE

: Lift the back panel over the tabs on the rear ledge of 

the fi replace. 

2. 

Align the screw holes in the top and bottom edges of the 
back panel with the holes in the fi replace ceiling and rear 
ledge. Secure using seven (7) #10-16 x 3/8 hex-head sheet 
metal screws provided with the fi rebox liner kit.

~

Fireplace 
Front

Left Side 
Panel

Back Panel

Refl ector

Tab

Rear Ledge

Figure 6 - 

 Accessing the control compartment

3. 

Remove the control compartment access door and gasket by 
removing the twelve (12) screws securing it. Set aside the 
screws, door, and gasket for later reinstallation 

(

Figure 6

)

.

Figure 7 -  Installing the refl ector

Figure 8 -  Installing the side panels

Figure 9 -  Installing the back panel

Summary of Contents for DRL6542 Series











Reviews: