3
INNOVATIVE HEARTH PRODUCTS • ENVY SERIES DIRECT-VENT GAS FIREPLACES • ENVY/ENVY CD 35/40/45 • INSTALLATION INSTRUCTIONS
Porcelain Firebox Liner Panels and Contemporary Floor
1.
Remove the four (4) porcelain firebox liner panels from the
packing material.
1.
(
Contemporary Fireplaces Only
) Remove the two (2) floor
panels from the packing material.
2.
(
Contemporary Fireplaces Only
) If installed, remove
the pilot media shield. Retain it and the screw for later
reinstallation.
3.
Identify the rear, left, right, and top firebox liner panels
(
Figure 1
).
4.
(
Contemporary Fireplaces Only
) Identify the the front and
rear floor panels (
Figure 1
).
5.
Carefully, install the rear firebox liner panel, upper edge first,
into the firebox, and position it against the rear wall with the
lower mounting tabs inserted into the mounting slots in the
firebox base. Insert the included 5/16 in. screw through the
upper mounting tab and use a nut driver to attach the rear
panel to the wall.
6.
(
Contemporary Fireplaces Only
) Carefully, install the rear
floor panel flush with the rear firebox liner panel. Ensure
the mounting holes are aligned with the screw holes in the
firebox floor.
NOTE:
Do not secure with screws.
7.
(
Contemporary Fireplaces Only
) Carefully, install the front
floor panel flush with the burner. Ensure the mounting holes
are aligned with the screw holes in the firebox floor.
NOTE:
Do not secure with screws.
8.
Carefully, install the left side firebox liner panel, positioned
flush against the rear firebox liner panel.
NOTE:
(
Contemporary Fireplaces Only
) The left side
firebox liner panel should be flush with the front and rear
floor panels.
9.
Carefully, install the right side firebox liner panel, positioned
flush against the rear firebox liner panel.
NOTE:
(
Contemporary Fireplaces Only
) The right side
firebox liner panel should be flush with the front and rear
floor panels.
10.
Carefully, install the top firebox liner panel by inserting it
into the top of the firebox all the way to the rear. Ensure the
front corners are above the left and right firebox liner panels
and then slide the top firebox liner panel to the front as far
as it will go. Lower the rear of the top firebox liner panel to
rest on the left and right firebox liner panels.
NOTE:
If having difficulty installing the top firebox liner
panel, lean the left and right side firebox liner panels in
to the center of the fireplace to create more room to aid
the installation.
11.
Using the four (4) included 5/16 in. screws, secure the side
firebox liner and (
Contemporary Fireplaces Only
) floor
panels to the firebox floor.
12.
(
Contemporary Fireplaces Only
) Install and secure the pilot
media cover with the included screw.
13.
(
Contemporary Fireplaces Only
) Install the glass media.
14.
Continue to
Fireplace Reassembly
.
NOTE:
If installing porcelain firebox liner panels in
Traditional fireplaces, omit the media, pilot media cover, and
Contemporary floors.
Ceramic Firebox Liner Panels
NOTE:
Ceramic firebox liner panels are only available for
traditional model ENVY fireplaces.
1.
Remove the four (4) ceramic firebox liner panels from the
packing materials.
2.
Identify the rear, left, right, and top firebox liner panels
(
Figure 1
).
3.
Carefully, install the rear firebox liner panel, upper edge first,
into the firebox, and position it against the rear wall.
4.
While holding the rear firebox liner panel in position,
carefully install the left side firebox liner panel into
the firebox.
5.
While holding the left side firebox liner panel in position,
carefully install the right side firebox liner panel into
the firebox.
6.
While holding the side firebox liner panels in position,
carefully install the top firebox liner panel into the firebox.
NOTE:
If having difficulty installing the top firebox liner
panel, lean the right side firebox liner panel in to the center
of the fireplace to create more room and aid the installation.
NOTE:
Handle the firebox liner panel carefully. Do not apply
too much pressure to the center of the panel at any point in
the installation.
7.
Ensure the top panel is positioned over both the left side and
right side firebox liner panels and that all panels are aligned
with the sides and rear of the firebox.
8.
Continue to
Fireplace Reassembly
.
FIREPLACE REASSEMBLY
1.
(
If Previously Removed
) Carefully, replace the ember base
and logs, and restore the lava rock to their original positions.
2.
(
If Previously Removed
) Reinstall the andirons.
3.
Carefully, position the glass door in front of the firebox
and hook the two upper spring-loaded latches over the
door frame.
4.
Hook the two lower spring-loaded latches over the
door frame.
5.
Use an ammonia-free glass cleaner and a soft, non-abrasive
cloth to remove fingerprints and smudges from the
glass door.
6.
Locate the surround trim assembly mounting slots on the
left and right sides of the firebox. Align the surround trim
assembly with the mounting slots and press in and down
to install it. Reinstall the left and right side finish trim gap
fillers.
7.
Use an ammonia-free glass cleaner and a soft, non-abrasive
cloth to remove fingerprints and smudges from the
surround trim assembly.
f i r e - p a r t s . c o m
