5
Name
Function
Handle
Grip
Brake lever
Stand grip
Stand
Front cover
Blade clutch lever
Rear roller
Bedknife adjustment handles
(left), (right)
Tires
Blade alignment clamp
Blade axis
Work attachment height adjustment
knobs (left), (right)
Front roller height adjustment knobs
(left), (right)
Front roller
Work attachment
Blades
Work attachment clutch knob
Engine switch
Fuel gauge
Fuel tank
Main clutch lever
●
Hold the grips to maintain the position and change the direction of the
mower during operation.
●
Hold the grips when operating the mower.
●
This lever is used to engage the brakes and stop the progress of the mower.
●
These grips are used when engaging/releasing the stand.
●
This stand is used to support the front roller and the mower when remov-
ing/installing the tires.
●
The front cover prevents the operator from becoming caught in and injured
by the clutch and transmission, which transmit the power from the engine.
Do not remove the cover while operating the mower.
●
This lever is used to "Start" and "Stop" the blades.
●
This roller is used to move the mower after removing the tires.
●
These handles are used to adjust the gap between the blades. One handle
is on the left side and one is on the right side.
●
These tires are used when transporting the mower to a workplace.
●
This clamp is used to manually rotate the blades.
●
This bolt is used during lapping work.
●
These knobs are used to adjust the height of the work attachment from the
ground. One knob is on the left side and one is on the right side.
●
These knobs are used to raise/lower the front roller to adjust blade height.
●
This roller is used to maintain the blades at a given height above the
ground to cut the grass at the determined height.
●
This roller is used to remove dead grass, and align grass grain and feed it
to the blades.
There are two types of rollers : a grooming cutter and brush reel.
●
These blades are used to cut grass.
●
This knob is used to switch between "Forward", "Stop", and "Reverse" for
the work attachment.
●
This switch is used to start and stop the engine. To start the engine, move
the switch to "ON". To stop the engine, move the switch to "OFF".
●
This gauge is used to indicate the amount of fuel remaining in the fuel tank.
●
This tank holds the fuel.
●
This lever is used to transmit power from the engine to the various parts,
and switch between "Start" and "Stop".
The blades and work attachment will rotate only when this lever is in the
"Start" position.
Throttle lever
Basket
One-touch lever
Basket stay
Fuel cock
Recoil starter
Strainer
Air cleaner
Muffler
Choke lever
Oil gauge
Blade height gauge
●
This lever is used to adjust the speed of the engine.
●
The basket is used to collect grass cuttings, and to prevent the operator
from coming into contact with the blades and/or the mower.
●
The one-touch lever is used to install or remove the reel unit.
●
The basket stay supports the basket. Also, it is used to install or remove
the reel unit.
●
This knob is used to supply fuel.
●
The starter is used to start the engine when the handle is pulled.
●
The strainer removes air and contaminants from the fuel.
●
The air cleaner prevents dust and contaminants from entering the air
sucked into the engine.
●
The muffler is used to reduce the noise of the engine.
●
The choke lever is used to increase the fuel mix when starting a cold en-
gine.
●
The oil gauge is used to check the remaining volume and contamination
level of engine oil.
●
The blade height gauge is used to fix the front roller and work attachment
at a specified height, by using screws in two locations to set blade height
and bring the front and rear rollers into contact.
Names of Parts
■ Names and Functions of Parts
