background image

Do not attempt to disassemble this monitor.

Battery replacement should only be performed by a qualified iHealth technician. To do otherwise will void your warranty

and possibly damage your unit.

Cuff replacement should only be performed by a qualified iHealth technician. To do otherwise

will possibly damage your unit.

WARRANTY INFORMATION

The iHealth View Wireless Blood Pressure Wrist Monitor is warranted to be free from defects in materials and workmanship

within one year from the date of purchase when used in accordance with the provided instructions. The warranty extends only to

the end user. We will, at our option, repair or replace without charge the iHealth View Wireless Blood Pressure Wrist Monitor

covered by the warranty. Repair or replacement is our only responsibility and your only remedy under the warranty.

EXPLANATION OF SYMBOLS

Symbol for "TYPE BF APPLIED PARTS" (cuff only)

Symbol for "THE OPERATION GUIDE MUST BE READ"

The sign background color: blue The sign graphical symbol: white

Symbol for "ENVIRONMENT PROTECTION – Waste electrical products should not be

disposed of with household waste. Please recycle where facilities exist. Check with your

local authority or retailer for recycling advice".

Symbol for "KEEP DRY"

Symbol for "WARNING"

Symbol for "MANUFACTURER"

Symbol for "SERIAL NUMBER"

Symbol for "EUROPEAN REPRESENTATIVE"

Symbol for "COMPILES WITH MDD93/42/EEC REQUIREMENTS"

iHealth is a trademark of iHealth Lab Inc.

"Made for iPod", "Made for iPhone", and "Made for iPad" mean that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that

the use of this accessory with iPod, iPhone, or iPad may affect wireless performance. iPad, iPhone, and iPod touch are

trademarks of Apple Inc., registered in the U.S. and other countries.

CONTACT AND CUSTOMER SERVICE

Manufactured for iHealth Lab Inc.

719N . Shoreline Blvd.,Mountain View, CA 94043, USA

Tel:+1-855-816-7705

www.ihealthlabs.com

Summary of Contents for View













Reviews: