Igloo STERYLIS ULTRA-220 Page 20 User Manual Download

Page: 20 / 32

STERYLIS ULTRA Operating Manual

NOTE!

CAUTION!

NOTE!

Ozone is a substance hazardous to human and animal health and life. Before

starting to operate the device in sterilisation mode, it is essential to read these

operating instructions, especially the safety sections!

Before starting the sterilisation mode, replace the activated carbon filter with

a standard filter. Such a filter is included with the device. When the sterilisation

mode is finished, the filter must be replaced with an activated carbon filter.

For instructions on how to replace the filters, see the section „CHANGING THE

FILTERS”.

In order to carry out the ozonisation process correctly and safely, it is necessary

to follow the instructions in chapter 8 - Procedure for carrying out the

ozonisation process!

In order for the sterilisation process to start, the ozone sensor has to undergo

preheating on its own!

Trying to start the sterilisation before this process

is completed is impossible! In this case, wait the required time. The heating

up of the ozone sensor is indicated by the slow blinking of the safe ozone

concentration indicator.

“UV-C air disinfection – silent mode” operating mode

“O

sterilisation” mode

To start the „UV-C air disinfection - silent mode” operating mode, press and hold the START button located

at the green silent mode light. The silent mode light will start blinking at a high frequency (the device

will check the proper functioning of the relevant actuators) and then it will start to light steadily and the

device will start working in the selected mode of operation. Confirmation of the disinfection mode is the

operation of the front panel illuminated on the unit. If any errors are detected, the unit will go into standby

mode and display the corresponding error codes on the display in the „STERILISTION” section.

The silent mode can also be directly selected if the unit is in standard disinfection or filtration mode. To

switch from standard disinfection or filtration mode to silent disinfection mode, press and hold the START

button located at the green silent mode light.

To interrupt the silent disinfection process, press and hold the START button next to the green silent mode

light again.

Summary of Contents for STERYLIS ULTRA-220

































Search results

Summary of Contents for STERYLIS ULTRA-220

Reviews:

Related manuals for STERYLIS ULTRA-220

Brands by name

Popular brands

Igloo STERYLIS ULTRA-220, User Manual

Search results

Summary of Contents for STERYLIS ULTRA-220

Reviews:

Related manuals for STERYLIS ULTRA-220

Brands by name

Popular brands