background image

en

16

User manual INNOVA

www.igloo.pl

• 

Place the plug of the connecting cable directly in plug-in socket (it is forbidden to connect the device by 

means of extension cords or dividers!)

• 

Turn on the main switch Fig.2/2 (p.14), which activates the thermostat, and then aggregate of the device

• 

Set the temperature on thermostat control panel Fig.2/1 (p.14) (thermostat service details on p.21 or 22)

• 

Turn on the lighting switch Fig.2/3 (p.14)

4. EXPLOITATION

Temperature of the cooled space and aggregate operating cycle may fluctuate. They depend on numerous factors, 

such as amount and temperature of products placed in the device and temperature of the surroundings.

The device should be placed in a dry and well-ventilated place, ensuring proper air exchange (distance between the 

wall and the device – min. 10 cm), out of sunlight, kept far from heat sources and devices enforcing air flow (ceiling 

and portable ventilators, blow-in heaters). The device functions properly in a room, where temperature falls within 

appropriate climatic class stated on the data plate. The operation of the device may worsen when it shall operate in 

temperature lower or higher than the stated temperature range.

      

 Remarks and indications

•  It is necessary to properly level the rack, which will prevent the device from noisy operation and will ensure 

proper outflow of the water (condensate) during defrosting.

•  After transporting the device, wait about 2 hours before its actuation.

•  In order to ensure proper conditions for the stored products, do not load the shelves completely. It is neces-

3. PREPARING THE DEVICE FOR EXPLOITATION

3.1. Requirements concerning the place of installation

• 

Verify whether the cross section of feeding conduits is proper for power consumption of the installed 

device.

• 

It is forbidden to connect the device by extension rods or dividers.

• 

The device should be connected to the separate, properly made electric circuit with plug-in socket with 

• 

   protecting pin (according to PBUE /Regulations concerning Electric Equipment Construction/)

3.2. Connection and actuation

• 

Unpack the device and remove the wooden platform from the basis Fig.3 (p.15)

• 

The device should be placed on an even and on a sufficiently hard base, and then level it with the help of 

levelling feet.

•  Remove the protection foil from the elements of the device (f. ex. from the inside of the device, display she-

lves, front fender beam)

•  If the user shall obtain a device partially disassembled to secure it during transportation, perform the following 

operations:

1.  Fix hooks in frame rails Fig.3 (p.15)

2.  Place shelves and/or baskets on hooks Fig.3 (p.15)

3.  (Concerns the devices with internal aggregate) Place the condensate container on the basis of the aggregate, 

under water outflow hose (does not concern devices with automatic condensate evaporation) Fig.5 (p.18) 

4.  (Concerns the devices to be mounted on central aggregate) Defrosting water outflow is located under the bot-

tom of the body (about 10mm from the back of the rack, in the middle part of the body), which needs toallow 

water outflow to the sewage grit

• 

The first cleaning of the device

 should be provide right after unpacking, and before turning it on. The unit 

should be cleaned with water at a temperature not exceeding 40°C with a neutral detergent. For washing 

and cleaning the equipment it is prohibited to use products containing chlorine and sodium varieties, which 

destroy the protective layer and components of the device! Any residue of adhesives or silicone on metal 

elements should be  removed only with extraction naphtha (not applicable to items made of plastic !). Do 

not use other organic solvents.

When cleaning the unit is prohibited to use water jet. The unit should be cleaned with a wet rag.

After installation of the device at the destination place it  should be left to rest for at least 2 hours before 

turning it on (for devices with built in compressor) to set the level of refrigerant in order to prevent problems 

with starting up the aggregate.

WARNING: Keep out the cooling circuit from damage!

Summary of Contents for INNOVA series












Reviews: