ifs MC352-4P-2S-V2 User Manual Download Page 3

 

 

2012/19/EU (WEEE directive): 

Products marked with this symbol cannot 

be disposed of as unsorted municipal waste in the European Union. For 

proper recycling, return this product to your local supplier upon the 

purchase of equivalent new

 

equipment, or dispose of it at designated 

collection points. For more information see: www.recyclethis.info.

 

 

 

2013/56/EU & 2006/66/EC (battery directive

): This product contains a 

battery that cannot be disposed of as unsorted municipal waste in the 

European Union. See the product documentation for specific battery 

information. The battery is marked with this symbol, which may include 

lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper 

recycling, return the battery to your supplier or to a designated collection 

point. For more information see: www.recyclethis.info.

 

Contact information  

 

EMEA: 

https://

firesecurityproducts.com

 

Australian/New Zealand: 

https://

firesecurityproducts.com.au/

 

Product 

documentation 

 

 

Please consult the following web link to retrieve the electronic version of the 

product documentation. The manuals are available in several languages. 

 

 

 

 

 

Summary of Contents for MC352-4P-2S-V2




















Reviews: