IFM O6H7 Series Operating Instructions Manual Download

Page: 7 / 13

7 Settings

7.1 Settings on the sensor
7.1.1 The sensor is to switch when the object is detected

Fig� 1

►

Position the object�

►

Press [OUT ON] for > 2 s�

> The yellow LED flashes�

> The setting of the range with object

is made by releasing [OUT ON]�

Fig� 2

►

Remove the object

►

Press [OUT OFF]�

> The setting of the range without

object is made by releasing [OUT

OFF]�

> The yellow LED goes out� Pro-

gramming is finished�

7.1.2 The sensor is not to switch when the object is detected

►

Position the object (see figure 1) and press [OUT

OFF

] for > 2 s�

►

Remove the object (see figure 2) and press [OUT ON]�

The setting can also be carried out first without object and then with object�

7.1.3 Set maximum range

►

Align the sensor so that no light is reflected�

1. The sensor is to switch when the object is detected

►

Press [OUT ON] for > 2 s, then [OUT OFF]�

2. The sensor is not to switch when the object is detected

►

Press [OUT OFF] for > 2 s, then [OUT ON]�

Summary of Contents for O6H7 Series














Search results

Summary of Contents for O6H7 Series

Reviews:

Related manuals for O6H7 Series

Brands by name

Popular brands

IFM O6H7 Series, Operating Instructions Manual

Search results

Summary of Contents for O6H7 Series

Reviews:

Related manuals for O6H7 Series

Brands by name

Popular brands