IFM O6H7 Series Operating Instructions Manual Download

Page: 12 / 13

7.2.3 Setting the range by means of background

If the object is not available, the range can be set using only the background�

The switching characteristics of the diffuse reflection sensor are the most

reliable if the range is set using the background and the object

(→ 7.2.2)

�

►

Start the LR DEVICE software�

►

Align the diffuse reflection sensor to the background (Fig� 4)�

►

Press button [Teach Custom - SP1 without target] in the LR DEVICE software�

> The switch point SP1 is just in front of the background (Fig� 5)�

Fig� 4:

Fig� 5:

SP1

Zone "object recognised"

7.2.4 Setting the maximum range

►

Start the LR DEVICE software�

►

Align the diffuse reflection sensor to an empty area without object or back-

ground�

> The diffuse reflection sensor must not receive any light from the object or the

background�

►

Press button [Teach Custom - SP1 without target] in the LR DEVICE software�

Summary of Contents for O6H7 Series














Search results

Summary of Contents for O6H7 Series

Reviews:

Related manuals for O6H7 Series

Brands by name

Popular brands

IFM O6H7 Series, Operating Instructions Manual

Search results

Summary of Contents for O6H7 Series

Reviews:

Related manuals for O6H7 Series

Brands by name

Popular brands