background image

5

UK

 

► Adhere to the principle of normally closed operation for all external safety 

circuits connected to the system�

 

► In case of faults within the fail-safe sensor which result in the defined safe 

state: take measures to maintain the safe state when the complete control 

system continues to be operated�

 

► Replace damaged units�

3  Items supplied

1 fail-safe sensor GG712S with 2 mounting nuts M18, 

1 operating instructions GG712S, ident no� 704229�
If one of the above-mentioned components is missing or damaged, please contact 

one of the ifm branch offices�

4  Functions and features

The fail-safe inductive sensor GG712S detects metal without contact� 
Safety function SF: The safe state (output stage switched off; logic "0") is achieved 

when undamping greater than or equal to the safe switch-off distance s

ar

 (→ 10 

Technical data)�  

Also observe the notes on installation of the sensor (→ 6 Installation)�
The fail-safe sensor conforms to Performance Level d to EN ISO 13849-1 as well 

as the requirements SIL 2 to IEC 61508 and fulfils SILcl 2 to IEC 62061�  
The unit corresponds to the classification I1A18SP2 to IEC 60947-5-2 for flush 

installation (→ 6 Installation)�
The fail-safe inductive sensor has been certified by TÜVNord� 

Summary of Contents for Efector 100 GG712S
















Reviews: