background image

UK

RFID UHF reader

5

2.7.2  FCC labelling

The unit complies with the applicable requirements to FCC Part 15�
Brand name: ifm electronic DTE900 and DTE910 RFID UHF reader for the 

US (FCC)
This reader is designed for operation in accordance with FCC Part 15�  
This device complies with part 15 of the FCC Rules� Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference, and, 

(2) This device must accept any interference received including interference that 

may cause undesired operation�
This unit complies with the FCC limit values for radiation exposure in a non-

controlled environment: When mounting and operating the unit, keep a minimum 

distance of 23 cm between the source of radiation and your own body�
In order to comply with the regulations of FCC Part 15 in the United States, the 

system must be professionally installed in order to guarantee compliance with 

the regulations for the certification according to Part 15�  The operator and the 

certified specialist carrying out the installation have the responsibility to ensure 

that only certified systems are applied in the United States� Using the system 

in any other combination (for example, several antennas at the same place 

transmitting the same information) is explicitly prohibited�

Modifications or conversions that are made to this unit without ifm 

electronic's explicit approval may make the FCC approval for the operation 

of this unit invalid.

Corresponding tests showed that this unit complies with the limit values for 

Class B digital devices, pursuant to part 15 of the FCC Rules� These limit values 

are designed to provide appropriate protection against harmful radio interference 

with installations for private use� This unit generates and uses energy in the 

radio frequency range and can also radiate it; if it is not installed and used in 

accordance with the regulations, the unit may cause harmful interference with 

radio communication� There is, however, no guarantee that no interference will 

occur in a specific installation� If this unit causes harmful interference to radio or 

television reception, which can be determined by turning the unit off and on, the 

user is encouraged to try to correct the interference by talking one or more of the 

following measures:

 

Readjust the receiving antenna or change its position�

 

Increase the distance between the unit and the receiver�

 

Connect the unit to a mains socket belonging to a different circuit than the one 

to which the receiver is connected�

 

Ask the dealer or an experienced radio and TV technician for advice�

Summary of Contents for DTE800
















Reviews: