background image

5

UK

the user and, if applicable, for any service personnel authorised by the 

manufacturer of the system�

•  Read this document before setting up the product and keep it during the entire 

service life�

•  The product must be suitable for the corresponding applications and 

environmental conditions without any restrictions�

• 

Only use the product for its intended purpose (→ Functions and features).

•  If the operating instructions or the technical data are not adhered to, personal 

injury and/or damage to property may occur� 

•  The manufacturer assumes no liability or warranty for any consequences 

caused by tampering with the product or incorrect use by the operator�

•  Installation, electrical connection, set-up, operation and maintenance of the 

product must be carried out by qualified personnel authorised by the machine 

operator�

•  Protect the device and the cables against damage�
•  Use the device outside petrol stations, fuel depots, chemical plants or blasting 

operations�

•  Do not transport and store any flammable gases, liquids or explosive 

substances near the device�

•  Operation of the device can affect the function of electronic devices that are not 

correctly shielded�

 -Disconnect the device in the vicinity of medical equipment�
 -Contact the manufacturer of the corresponding device in case of any 

interference�

•  Because of the requirements for electromagnetic interference emissions, the 

device is intended for use in industrial environments� The device is not suitable 

for use in domestic areas�

•  Device safety: Use the device indoors only�

3  Functions and features

The RFID evaluation unit DTE105 integrates an Ethernet TCP/IP interface and 4 

channels for the connection of field devices� Each channel can be used either for 

the connection of an RFID antenna or as input/output to IEC 61131�

Summary of Contents for DTE105





















Reviews: