IFM Electronic efector 300 SM6100 Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 31

background image

15

UK

5.3 Protection against high medium temperatures

For medium temperatures over 50 °C some parts of the housing can heat up to

over 65 °C�

► Protect the housing against contact with flammable substances and uninten-

tional contact�

6 Electrical connection

The unit must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply to EN50178, SELV, PELV�

► Disconnect power�

► Connect the unit as follows:

Pin1

Ub+

Pin3

Ub-

Pin4

(OUT1)

Switching signal: limit values for volumetric flow�

Switching signal: quantity meter reached preset value�

Pulses: 1 pulse every time the defined volumetric flow quantity is reached�

Pin2

(OUT2/InD)

Switching signal: limit values for volumetric flow�

Switching signal: limit values for temperature�

Analogue signal for volumetric flow�

Analogue signal for temperature�

Input for signal “meter reset”�

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

«
...
13
14
15
16
17
...
»

Summary of Contents for efector 300 SM6100
































Reviews:

No comments

Related manuals for efector 300 SM6100

Brand: PASCO Pages: 3

Brand: Endress+Hauser Pages: 88

Brand: East Tester Pages: 27

Brand: Parkside Pages: 199

PHYSICS line C.A 832

Brand: Chauvin Arnoux Pages: 43

Brand: Orange Research Pages: 2

Brand: Sub Aqua Pages: 4

Liebert MBX Busway

Brand: Vertiv Pages: 16

Brand: DynAmp Pages: 43

EnviroMentor Field Finder

Brand: Radians Innova Pages: 12

Brand: Parkside Pages: 165

Brand: RX Pages: 8

DMX Laser40 FScan

Brand: KAM Pages: 4

Brand: PKP Pages: 20

Brand: ADCMT Pages: 28

Brand: Landtek Pages: 3

Brand: ADA INSTRUMENTS Pages: 48

Brand: Kobold Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands