background image

UK

Device manual CR3105/CR3106

5

2  Safety instructions

These instructions are part of the device� They contain information and illustrations 

about the correct handling of the device and must be read before installation or 

use� 

2.1  General

Follow the operating instructions�  Non-observance of the instructions, operation 

which is not in accordance with use as prescribed below, wrong installation or 

incorrect handling can affect the safety of operators and machinery� 

The device must only be installed, connected and put into operation by a qualified 

electrician� 

Disconnect the device externally before handling it�
In case of malfunction of the device or queries please contact the manufacturer� 

Tampering with the device can seriously affect the safety of operators and 

machinery� This is not permitted and leads to an exclusion of liability and warranty�

2.2  Air traffic

The device must not be operated on board of aircraft� 

Using it in an aircraft can affect the navigation and communication systems� An 

offence can lead to legal action against the offender�

2.3  Explosive substances

In general, radio equipment must not be used in the vicinity of petrol stations, fuel 

depots, chemical plants or blasting operations� 

Do not transport and store any flammable gases, liquids or explosive substances 

in the part of the vehicle where the device is installed�

2.4  Electronic devices

Operation can affect the function of electronic devices that are not correctly 

shielded� 

Disconnect the unit in the vicinity of medical equipment� Please contact the 

manufacturer of the corresponding device or equipment in case of problems�

2.5  Antenna(s)

Operation without antenna(s) can lead to destruction of the device�

2.6  Loss/theft of the SIM card

To prevent misuse, immediately inform your network operator in case of loss or 

theft of the SIM card or the device�

Summary of Contents for CR3105














































Reviews: