IEI Technology ROCKY-3786EV User Manual Download Page 15

Page: 15 / 147

Page 15

MODEL NAME

ROCKY-3786EV CPU Card

Page 15

1 x IrDA connector

1 x Keyboard/Mouse connector

1 x LAN LED connector

1 x Multi panel connector

1 x Parallel port connector

2 x SATA connectors

2 x Serial port connectors

2 x USB 1.1 connectors

4 x USB 2.0 connectors (optional)

1 x VGA connector

The ROCKY-3786EV CPU board has the following connectors on the board rear panel:

1 x Audio Line Out connector

2 x RJ-45 Ethernet connectors

1 x Keyboard/Mouse connector

1 x VGA connector

The location of these connectors on the CPU Card can be seen in

Figure 3-21

. These

connectors are fully described in

Chapter 2

NOTE:

There are no configuration jumpers or connectors on the soldering side.

1.2.2 Technical Specifications

ROCKY-3786EV CPU board technical specifications are listed in

Table 1-2

. Detailed

descriptions of each specification can be found in

Chapter 2

SPECIFICATION

CPUs Supported

Intel

Pentium® III, Celeron®, or VIA C3

Chipsets

Northbridge: Intel

815E

Southbridge: Intel® ICH2

I/O Controller

IT8712

Summary of Contents for ROCKY-3786EV




















































































































































Search results

Summary of Contents for ROCKY-3786EV

Reviews:

IEI Technology ROCKY-3786EV, User Manual, Page: 15 / 147

Search results

Summary of Contents for ROCKY-3786EV

Reviews: