background image

 

PAC-1700G QIG                    IEI Technology Corp.                                    Page  8 

 
 

 

Figure 24: Slide the CPU Card into the Socket 

Step 4: 

To secure the CPU card, reinsert the previously 

removed slot cover retention screw.

Step 0:

 

 

STEP 12: PCI/ISA EXPANSION CARD 
INSTALLATION 

The PAC-1700G supports up to six PCI/ISA expansion cards. If you 
wish to install a PCI expansion card or an ISA expansion card 
please follow the instructions below: 

Step 1: 

Remove the slot cover at the back of the chassis. To do 
this, remove the slot cover retention screw at the top of 
the slot cover. 

Step 2: 

Slide the PCI/ISA expansion card into the reserved 
PCI/ISA socket on the backplane. 

Step 3: 

To secure the PCI/ISA expansion card, reinsert the 

previously removed slot cover retention screw.

Step 0:

   

STEP 13: TOP COVER REINSTALLATION 

After you have completed the above procedures, the top cover can 
be reinstalled.

 

To reinstall the top cover, slide the cover back over 

the chassis and reinsert the six previously removed retention 
screws. 

 
STEP 14: WALL-MOUNT PLATES 
INSTALLATION 

 
Two wall-mount plates are shipped with the PAC-1700G chassis. 
The wall-mount plates are installed on the sides, at the bottom of the 
chassis. Each plate is secured to the chassis with three retention 
screws. To install the wall-mount plates, please follow the steps 
below: 

Step 1: 

Align the retention screw holes on the side of the 
chassis with the retention screw holes in the wall-mount 
plate. 

Step 2: 

To secure the wall-mount plates, insert three retention 

screws into each wall-mount plate.

Step 0:

 

 

 

Figure 25: Wall-mount Plate Retention Screws 

CHASSIS MAINTENANCE 

 

 

F

AN 

R

EPLACEMENT

 

 

 NOTE: 

Please ensure that the power of the computer is switched off 

before you replace a fan. 

 

 
There is one 8 cm cooling fan inside the PAC-1700G chassis. To 
replace a fan, please follow the steps below: 

Step 1: 

Flip open the fan filter cover. 

 

 

Figure 26: Open the Fan Filter Cover 

Step 2: 

Open the front panel cover. 

 

 

Figure 27: Open the Front Panel Cover 

Step 3: 

Remove the four front panel frame retention screws to 
remove the front panel frame. 

 

 

Figure 28: Front Panel Retention Screws 

Step 4: 

To remove the fan, remove the four fan retention screws. 

Summary of Contents for PAC-1700G










Reviews: