IEI Technology IMBA-Q470 User Manual Download Page 92

Page: 92 / 102

IMBA-Q470 ATX Motherboard

Page 92

4.6

Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

4.6.1

SATA Drive Connection

The IMBA-Q470 is shipped with two SATA drive cables. To connect the SATA drives to the

connectors, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the SATA drive connectors are shown

Chapter 3

Step 2:

Insert the cable connector

. Insert the cable connector into the on-board SATA

drive connector until it clips into place. See

Figure 4-7

Figure 4-7: SATA Drive Cable Connection

Step 3:

Connect the cable to the SATA disk

. Connect the connector on the other end

of the cable to the connector at the back of the SATA drive. See

Figure 4-8

Step 4:

Connect the SATA power cable

. Connect the SATA power connector to the

back of the SATA drive. See

Figure 4-8

Step 0:

Summary of Contents for IMBA-Q470







































































































Search results

Summary of Contents for IMBA-Q470

Reviews:

Related manuals for IMBA-Q470

Brands by name

Popular brands

IEI Technology IMBA-Q470, User Manual

Search results

Summary of Contents for IMBA-Q470

Reviews:

Related manuals for IMBA-Q470

Brands by name

Popular brands