manualshive.com logo in svg

IEI Technology IMB-ADL-H610, User Manual

Share
Download
IEI Technology IMB-ADL-H610 User Manual Download Page 93

 

 

IMB-ADL-H610 Micro ATX Motherboard 

Page  93 

➔

 

Intel (VMX) Virtualization Technology [Enabled] 

Use the 

Intel (VMX) Virtualization Technology 

option to enable or disable virtualization 

on the system. When combined with third party software, Intel® Virtualization technology 

allows several OSs to run on the same system at the same time. 

➔

 

Disabled 

 

Disables Intel Virtualization Technology. 

➔

 

Enabled 

D

EFAULT

 

Enables Intel Virtualization Technology. 

➔

 

Active Performance Cores [All] 

Use  the 

Active  Performance  Cores 

BIOS  option  to  enable  numbers  of  P-cores  in  the 

processor package. 

➔

 

 

All

 

 

D

EFAULT

 

Enable all P-cores in the processor package. 

➔

 

➔

 

➔

 

➔

 

➔

 

➔

 

➔

 

➔

 

 

1 

2 

3 

4 

5 

6 

7 

 

Enable one P-core in the processor package. 

Enable two P-core in the processor package. 

Enable three P-core in the processor package 

Enable four P-core in the processor package 

Enable five P-core in the processor package 

Enable six P-core in the processor package 

Enable seven P-core in the processor package 

➔

 

Active Efficient Cores [All] 

Use the 

Active Efficient

 

Cores 

BIOS option to enable numbers of E-cores in the processor 

package. 

➔

 

All

 

 

D

EFAULT

 

Enable all E-cores in the processor package. 

➔

 

0 

 

Enable zero E-core in the processor package. 

➔

 

1 

 

Enable one E-cores in the processor package. 

➔

 

2 

 

Enable two E-cores in the processor package. 

➔

 

3 

 

Enable three E-cores in the processor package. 

Summary of Contents for IMB-ADL-H610



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands