manualshive.com logo in svg

IEI Technology IMB-ADL-H610, User Manual

Share
Download
IEI Technology IMB-ADL-H610 User Manual Download Page 20

 

 

IMB-ADL-H610 Micro ATX Motherboard 

Page  20 

Digital I/O 

One 12-bit digital I/O   

Ethernet 

Two RJ-45 GbE ports 

Fan 

One 4-pin CPU smart fan connector 

Two 4-pin system smart fan connectors

 

Front Panel 

One 14-pin header (power LED, HDD LED, speaker, power 

button, reset button) 

I

2

C

 

One 4-pin wafer connector 

LAN LED 

Two

 

2-pin header for LAN1 LED and LAN2 LED 

Serial ATA 

Four SATA 6Gb/s connectors     

Serial Ports 

Two RS-232/422/485 via DB-9 (RS-485 support AFC) 

4 x RS-232 via internal box header 

SMBus 

One 4-pin wafer connector 

USB Ports 

Two USB 3.2 Gen 2(10Gb/s) ports (Type A) on rear panel 

Two USB 3.2 Gen 1(5Gb/s) ports (Type A) on rear panel 

Four USB 2.0 ports (Type A) on rear panel   

Two USB 2.0 ports via internal pin header   

Environmental and Power Specifications 

 

Power Supply 

AT/ATX power supply 

Support AT/ATX mode 

ErP/EuP compliant 

Power 

Consumption 

[email protected], [email protected], [email protected], [email protected] 

(Intel® Core™ i9-12900E CPU with 8 GB 3200 MHz DDR4 

memory, EuP mode enabled) 

Operating 

Temperature 

-0ºC ~ 60ºC 

Storage 

Temperature 

-30ºC ~ 70ºC 

Operating Humidity 

5% ~ 95% (non-condensing) 

Physical Specifications 

Summary of Contents for IMB-ADL-H610



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands