manualshive.com logo in svg

IEI Technology IMB-ADL-H610, User Manual

Share
Download
IEI Technology IMB-ADL-H610 User Manual Download Page 85

 

 

IMB-ADL-H610 Micro ATX Motherboard 

Page  85 

5.1.3

 

Getting Help 

When 

F1

 is pressed a small help window describing the appropriate keys to use and the 

possible selections for the highlighted item  appears. To exit the Help Window, press the 

E

SC

 key. 

5.1.4

 

Unable to Reboot after Configuration Changes 

If  the  computer  cannot  boot  after  changes  to  the  system  configuration  is  made,  CMOS 

defaults. Use the clear CMOS button described in 

Chapter

 

4

. 

5.1.5

 

BIOS Menu Bar 

The 

menu bar

 on top of the BIOS screen has the following main items: 

▪

 

Main – Changes the basic system configuration. 

▪

 

Advanced – Changes the advanced system settings. 

▪

 

Chipset – Changes the chipset settings. 

▪

 

Security – Sets User and Supervisor Passwords. 

▪

 

Boot – Changes the system boot configuration. 

▪

 

Save & Exit – Selects exit options and loads default settings 

The  following  sections  completely  describe  the  configuration  options  found  in  the  menu 

items at the top of the BIOS screen and listed above. 

 

 

Summary of Contents for IMB-ADL-H610



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands