IEI Technology ICE-BT-T10-E38151 User Manual Download Page 57

Page: 57 / 97

ICE-BT-T10 COM Express Module

Page 47



Disabled

Legacy USB support disabled



Auto

Legacy USB support disabled if no USB devices are

connected

5.4 Chipset

Use the

Chipset

menu (

BIOS Menu 14

) to access the North Bridge and South Bridge

configuration menus.

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu

may cause the system to malfunction.

Main

Advanced

Chipset

Security

Boot

Save & Exit

> North Bridge
> South Bridge

North Bridge Parameters.

---------------------



: Select Screen





: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 14: Chipset

Summary of Contents for ICE-BT-T10-E38151


































































































Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands

IEI Technology ICE-BT-T10-E38151, User Manual

Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands