IEI Technology ICE-BT-T10-E38151 User Manual Download Page 65

Page: 65 / 97

ICE-BT-T10 COM Express Module

Page 55



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled D

EFAULT

OEM Logo displayed instead of POST messages



UEFI Boot [Disabled]

Use the

UEFI Boot

BIOS option to allow the system to boot from the UEFI devices.



Enabled

Enables to boot from the UEFI devices.



Disabled D

EFAULT

Disables to boot from the UEFI devices.



OS Selection [Windows 8.X]

Use the

OS Selection

option to select an operating system for the system.



Windows

8.X

EFAULT



Android



Windows



Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled D

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force

BIOS

EFAULT

Sets display mode to force BIOS.



Keep

Current

Sets display mode to current.

Summary of Contents for ICE-BT-T10-E38151


































































































Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands

IEI Technology ICE-BT-T10-E38151, User Manual

Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands