IEI Technology ICE-BT-T10-E38151 User Manual Download Page 54

Page: 54 / 97

ICE-BT-T10 COM Express Module

Page 44

5.3.7 IDE Configuration

Use the

IDE Configuration

menu (

BIOS Menu 11

) to change and/or set the configuration

of the SATA devices installed in the system.

Advanced

IDE Configuration

Serial-ATA(SATA) [Enabled]
SATA Mode

[IDE Mode]

SATA1
Not Present

SATA2
4GB NANDrive (3.9GB)

Enable or disable SATA
Device.

---------------------



: Select Screen





: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 11: SATA

Configuration



Serial-ATA (SATA) [Enabled]

Use the

Serial-ATA (SATA)

option to enable or disable the SATA controller.



Enabled D

EFAULT

Enable SATA controller.



Disabled

Disable SATA controller.



SATA Mode Selection [IDE]

Use the

SATA Mode Selection

option to configure SATA devices.



IDE

EFAULT

Configures SATA devices as normal IDE device.



AHCI

Configures SATA devices as AHCI device.

Summary of Contents for ICE-BT-T10-E38151


































































































Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands

IEI Technology ICE-BT-T10-E38151, User Manual

Search results

Summary of Contents for ICE-BT-T10-E38151

Reviews:

Related manuals for ICE-BT-T10-E38151

Brands by name

Popular brands