manualshive.com logo in svg

IEC miniReStoramod, Installation, Operation & Maintenance Manual, Page: 13 / 28

Share
Download
IEC miniReStoramod Installation, Operation & Maintenance Manual Download Page 13

Modular Hi-Rise Replacement Series – MIY

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

13

SECTION TWO — Product Line Specific Demolition & Installation, Cont’d.

Figure 4. Top Opening

 

24.  If there is a side/front supply, install the supply 

air grille(s) into the painted, top supply-grille 
transition panel (Figure 6). For top supply only, 
install the painted top blank-off panel instead 
(Figure 5).

Figure 5. Top Blank-off Panel 

Figure 6. Top Supply Grille Transition Panel 

25.  Attach the louvered, return-air deco panel to the 

new chassis, using both of the 5/16” hex cam-
locks.

26.  Installation complete. Clean up work area.

Submittals and product literature detailing unit operation, 
controls, and connections should be thoroughly reviewed 
BEFORE beginning the connection and testing of risers 
and piping.

To assure optimal unit performance, the supply 
connection(s) are marked on the unit’s coil with an “S” 
meaning supply or inlet and “R” meaning return or outlet 
indicating flow direction to and from the coil. Blue letters 
mark the chilled water connections and red letters mark 
the hot water connections.

Summary of Contents for miniReStoramod





























Reviews:

No comments