IDT 89HPEB383 User Manual Download

Page: 89 / 264

9. Error Handling > PCI as Originating Interface

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

Header is logged in the

“PCIe Secondary Header Log 1 Register”

and ERR_PTR is updated in the

“PCIe Secondary Error Capabilities and Control Register”

if R_TA Mask bit is clear in

“PCIe

Secondary Uncorrectable Error Mask Register”

and ERR_PTR is not valid

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of R_TA bit in

“PCIe Secondary Uncorrectable Error Severity Register”

if R_TA Mask bit is clear in

“PCIe

Secondary Uncorrectable Error Mask Register”

and either SERR_EN bit is set in

“PCI Control and

Status Register”

or FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and the SERR_EN bit is set in

“PCI Control and Status Register”

FTL_ERR_DTD/NFTL_ERR_DTD bit is set in

“PCIe Device Control and Status Register”

9.3

PCI as Originating Interface

This section describes how the PEB383 handles errors for upstream transactions from PCI to PCIe (see

Figure 24

). The bridge supports TLP poisoning as a Transmitter to permit proper forwarding of parity

errors that occur on the PCI Interface.

Figure 24: Transaction Error Forwarding with PCI as Originating Interface

Table 15

provides the error forwarding requirements for Uncorrectable data errors detected by the

PEB383 when a transaction targets the PCIe Interface. Posted and non-posted write data received on
the secondary PCI Interface with bad parity are forwarded to PCIe as Poisoned TLPs.

Table 15: Error Forwarding Requirements for Received PCI Errors

Received PCI Error

Forwarded PCIe Error

Write with Uncorrectable Data Error

Write request with Poisoned TLP

Req uestor

or Del ayed

Transaction

completer

PEB38x

C ompleter

PCIe

(Desti nati on

Interface)

PCI

(Origi nating

Interface)

Summary of Contents for 89HPEB383









































































































































































































































































Search results

Summary of Contents for 89HPEB383

Reviews:

Related manuals for 89HPEB383

Brands by name

Popular brands

IDT 89HPEB383, User Manual

Search results

Summary of Contents for 89HPEB383

Reviews:

Related manuals for 89HPEB383

Brands by name

Popular brands