idomus IDO PRO (HL), Mounting, Operation And Maintenance Instructions, Page: 5 / 24

5
4.1. Cleaning
In order to maintain the quality of the surface, regularly clean the
surface no rarer than every three months (the external side of the doors
and sealing intermediates). Clean water is suffi cient for cleaning
and maintenance. In the event of large pollution, please use warm
water and neutral, non-scouring detergents (household detergent,
pH 7) for cleaning. Easy slippage of side sealing intermediates
must be ensured, which is why the area of their slippage must be
constantly cleaned and lubricated with PTFE lubricant. You can fi nd
more thorough information about the cleaning of the doors in “User
instruction”.
4.2 Control
Only the persons, who were instructed, must control the doors A
thorough control and maintenance instruction of the sectional doors
is described in “User’s Instruction”, which is provided together with
sectional garage doors to their owner.
• Only use the doors when there are no obstacles in their
pathway. You cannot stand or walk under the moving doors (remove
all of the items that are in the area of the doors);
• Open and close the doors only by using the supplied control
elements (rope or automatic gear, handle);
• If the doors are complemented with an automatic gear, the
door lock must be removed;
• If, during operation, the defects of separate parts of the
doors become evident (the coils of lifting cable began rupturing, the
tensioning of the springs became weakened, if it is hard to lift the
doors, if, during lifting/lowering, strange noises are heard etc.), please
address the company that mounted the doors in order to perform
guarantee or post-guarantee maintenance;
• If protection against cable rupture or spring breaking turns
on, promptly address the company that mounted the doors;
• Never change the door structure and remove the elements
yourself.
5. DOOR MAINTENANCE AND TECHNICAL MAINTENANCE
Only a qualifi ed specialist must perform the maintenance of the
doors. The doors must be regularly maintained and inspected from
their fi rst commissioning and not rarer than once per year. The
inspection, technical maintenance and repair works must be recorded
in writing and kept in the door passport for the full period of the
product’s operation
A high value tensioning and torsion moment is affecting
the door springs, cables and lower wheel holders, which is why, prior
to changing or inspecting them, please protect the plane of the doors
against uncontrolled movements. The damaged cables and springs
poses a threat of injury, which is why, they must be continuously
inspected.
Right after mounting the doors:
• Check whether the doors open easily, when the doors are
closed, the wheels must easily rotate. If need be, adjust the wheels;
• Check whether the weight of the plane has been properly
aligned: manually open the doors up to half height. In this position,
the doors must fasten themselves (if the doors do not fasten and
come down, tension the springs);
• Chen and, if need be, tension all of the fastening points on
the doors and on the wall of the building;
• Lubricate the rails, bearings of the doors and wheel
holders, the rivets of middle and side hinges (recommendation: PTFE
lubricant);
• Lubricate the intermediates (recommendation: special
rubber lubricant or vaseline).
After 3 months:
Check the balancing system, tension/loosen the springs; •
• Perform thorough inspection as right after the mounting of
the doors, but prior to their commissioning.
Every 6 months or right after 750 cycles:
• Check whether side, upper and lower intermediates do not
have damages, cracks or signs of wear and tear;
• Perform thorough inspection as right after the mounting of
the doors, but prior to their commissioning;
• Lubricate the rails, bearings of the doors and wheel
holders, the rivets of middle and side hinges (recommendation: PTFE
lubricant);
• Lubricate the intermediates (recommendation: special
rubber lubricant or vaseline);
• Clean the segments, do not use abrasive detergents
(recommendation: water);
Wax the segments (recommendation: car wax); •
• Remove the fi lth from the doors and around them.
Every 12 months or right after 1500 cycles:
• Check, whether the cables and lower holders did not
become worn;
• Check the balancing of the doors and, if need be, adjust it;
• Check whether the hinges did not become worn and/or
damaged;
• Check whether the pulleys did not become worn and/or
damaged;
• Check whether the wheels did not become worn and/or
damaged;
• Check the fastenings of the springs;
• Check the closing force of the plane of the doors;
• Perform thorough inspection as right after the mounting of
the doors, but prior to their commissioning;
• Check whether the side, lower and upper intermediates did
not become worn and damaged;
• Check whether the segments of the doors did not become
worn and/or damaged.
6. MALFUNCTIONS AND ELIMINATION OF DEFECTS
If malfunctions or damages of the doors occur (the movement of
the doors is diffi cult or there are damaged elements), please address
the qualifi ed specialist. It is prohibited to operate such doors! Due to
uncontrollable movements of the plane of the doors (especially in the
event of broken spring and turning on of the protection mechanism),
people may be hurt or items damaged.
IDO- PRO doors are complement with spring protection mechanisms,
which turn on after the breaking of the spring.
7. DISMANTLING OF DOORS
The dismantling of the doors is performed in reverse order to
mounting of them (by adhering to this mounting instruction in reverse
order than indicated), by adhering to the same requirements and
using the same safety measures.
A qualifi ed specialist must dismantle the doors.
8. DOCUMENTATION
These documents must be submitted to the end-user (owner of the
doors) after the mounting of them (which the user must preserve for
the whole operation period of the doors):
• Door Mounting Instructions (this instruction containing
referencing to the mounting, dismantling and technical maintenance
of the doors);
User’s Instruction. Door Passport; •
•
•
Declaration of Performance;
Declaration of Conformity (for doors being controlled
through electrical gear);
Right after mounting the doors, a qualifi ed specialist, who mounted
them, must familiarize the user with these documents and their
content, as well as to train the user on how to control the doors and
what to do in the event of their malfunctions.
9. DISPOSAL Properly dispose of the product’s
packaging and the used elements. Do not throw away the used
elements together with household waste. Transfer them to the
specialized waste collection point or address the distributor of the
product. If you need more information on how to dispose such waste,
address the authorities of your city or waste handling organizations.
EN