Idis DR-6532P-A Page 31 Operation Manual Download

Page: 31 / 139

Part 1 - Getting Started

Audio Recording

If the Record Audio option under

Record Setup

General

has been enabled the camera will record audio

along with video. For more information, refer to the

Stream II on page 54, Record Setup on page 57

Check your local laws and regulations on making audio
recordings.

Video Recording Playback

You can play back video recordings by using mouse or
remote control.

•

The initial video playback point in Search mode is
the recording's last playback point or the end of the
recording data.

•

Audio playback of the selected recording is available
in full screen mode only.

•

Covert protection on cameras also applies to video
recording playback.

All Channel Playback

Press the

Menu

button while in Live mode.

Select the Search Mode icon and then select

Time-Lapse Search

Event Log Search

Thumbnail Search

The selected search mode will be initiated.

For more information on data search, refer to the

Part 3 -

Search on page 117

Summary of Contents for DR-6532P-A












































































































































Search results

Summary of Contents for DR-6532P-A

Reviews:

Related manuals for DR-6532P-A

Brands by name

Popular brands

Idis DR-6532P-A, Operation Manual

Search results

Summary of Contents for DR-6532P-A

Reviews:

Related manuals for DR-6532P-A

Brands by name

Popular brands