manualshive.com logo in svg

iDirect iNFINITI 3000, Installation And Commissioning Manual, Page: 39 / 72

Share
Download
iDirect iNFINITI 3000 Installation And Commissioning Manual Download Page 39

35

iDirect iNFINITI series Installation and Commissioning Guide, Release 7.0

8

Fine-tune the Antenna Pointing and Cross Polarization

Complete fine-tuning the antenna pointing and cross polarization from within the iSite GUI.

8.1

Set up the Satellite Router for Cross Polarization

8.2

Set up iSite for Cross Polarization

The remote portion of the cross polarization test is conducted from the iSite GUI. 

Figure 8-1: iSite Cross Polarization

1.

Disable the power to the Satellite Router to set it up for cross polarization.

2.

Disconnect the receive IFL cable from the Satellite Router.

3.

Disconnect the transmit IFL cable from the DVM and connect it to the BUC.

1.

Power on the Satellite Router and ensure that you have IP connectivity to it 
from your laptop.

2.

Launch iSite and connect to the Satellite Router using its IP address

3.

Log in as Admin with a valid password.

4.

In the iSite main menu, select 

Configure

, select 

Align Antenna

, and then 

click 

Cross Polarization

.

Summary of Contents for iNFINITI 3000









































































Reviews:

No comments