background image

Safety

 

V. 1.0

 

6

 

SK300 CE

 

 

 

 

 

Safety

 

 
 
 

WARNlNG

 

Read the manual before you install or use the machine. Failure to do so can result in personal 
injury, death or property damage.

 

 

2.1 

lntended use

 

 

The machine is designed to shake colorants in a can. Any other use of the machine is strictly forbidden.

 

 

2.2 

Liability

 

 

2.2.1 General 

liability

 

Our machines and accessories are fully compliant with the CE regulations. Any modification can result in not 
fulfilling the CE safety requirements and is therefore not allowed. Fast & Fluid Management B.V. will not accept 
any responsibility in case of modifications to machines and/or accessories.

 

 

Fast & Fluid Management B.V. is not liable if you do not follow the rules below:

 

-  The machine is for indoors use only.

 

-  This machine may only be used for commercial settings. The machine is not a household appliance.

 

-  Observe all local safety regulations.

 

-  Strictly obey the safety instructions in this manual.

 

-  Mind the minimal requirement of the building structure of the load capacity of the floor.

 

-  Place machine in a well-lit and well-ventilated room.

 

-  Install and connect the machine according to the instructions in this manual.

 

-  Connect the machine to a grounded wall socket.

 

-  Do not use extension cords or inadequately rated power cables.

 

-  Make sure that the power cable is freely accessible.

 

-  Do not place objects on top of the machine.

 

-  Keep lids, panels, and covers closed and in place whenever possible.

 

-  Do not use a damaged machine. When you have doubts, contact your supplier.

 

-  Keep the machine in good condition.

 

-  Clean the machine at the intervals and when dirty.

 

-  Make sure that defective parts are immediately replaced.

 

-  Remove spilled liquids immediately, and unplug the machine in case of large spillages (> 500mL).

 

-  Replace parts only with original Fast & Fluid Management B.V. spare parts.

 

 

All maintenance beyond the scope of this manual must be carried out by a qualified service technician that Fast 
& Fluid Management B.V. has trained and certified.

 

 

2.2.2 Machine-specific 

liability

 

The machine cannot be used in an environment where explosive vapours may occur (ATEX zone). Colorants 
that contain flammable solvents can be mixed, as long as they are packed in a suitable UN approved container.

 

 

Please consult the health & safety officer of your paint supplier and/or colorant supplier on how to avoid the 
emergence of hazardous situations like personal harm or the risk for fire and explosion.

 

Summary of Contents for FAST&FLUID SK300 CE
























Reviews: