background image

6

2

Safety

2.1

Intended use

The machine is designed to dispense colorants into a can. Any other use of the machine is strictly forbidden.

2.2

Liability

2.2.1

General liability

Our machines and accessories are compliant with their market specific safety requirements. For some markets 
machines need a certification to prove the machine complies with the essential requirements concerning safety. 
Any modification can result in not fulfilling the market-specific machine safety requirements and is therefore not 
allowed. Fast & Fluid Management B.V. will not accept any responsibility in case of modifications to machines 
and/or accessories.

Fast & Fluid Management B.V. is not liable if you do not follow the rules below:
-

The machine is for indoors use only.

-

This machine may only be used for commercial settings. The machine is not a household appliance.

-

Observe all local safety regulations.

-

Strictly obey the safety instructions in this manual.

-

Mind the minimal requirement of the building structure of the load capacity of the floor.

-

Place machine in a well-lit and well-ventilated room.

-

Install and connect the machine according to the instructions in this manual.

-

Connect the machine to a grounded wall socket.

-

Do not use extension cords or inadequately rated power cables.

-

Make sure that the power cable is freely accessible.

-

Do not place objects on top of the machine.

-

Keep lids, panels, and covers closed and in place whenever possible.

-

Do not use a damaged machine. When you have doubts, contact your supplier. See

§ 5.2

.

-

Keep the machine in good condition. 
-

Clean the machine at the intervals and when dirty.

-

Make sure that defective parts are immediately replaced.

-

Remove spilled liquids immediately, and unplug the machine in case of large spillages (> 500mL).

-

Replace parts only with original Fast & Fluid Management B.V. spare parts.

All maintenance beyond the scope of this manual must be carried out by a qualified service technician that Fast 
& Fluid Management B.V. has trained and certified.

2.2.2

Machine-specific liability

This machine is designed to dispense colorants into a can in non-hazardous conditions.
Please consult the health & safety officer of your paint supplier and/or colorant supplier on how to avoid the
emergence of hazardous situations like personal harm or the risk for fire and explosion.

WARNING

Read the manual before you install or use the machine. Failure to do so can result in personal 
injury, death or property damage.

Safety 

X-Smart

V 1.4

Summary of Contents for Fast & Fluid X-SMART























Reviews: