Idemia VisionPass Installation Manual Download

Page: 75 / 76

VisionPass - 2019_2000045728

10.1 > Troubleshooting

The terminal IP address is unknown or it is not possible to connect to the terminal

Use terminal interface to configure a valid set of network parameters in your terminal.

The sensor is switched off

Check that the database contains at least one record.

Check that the identification mode is enabled.

The terminal returns erratic responses to Ping commands

Check the subnet mask.

Ask the network administrator for the correct value.

Check that each device connected to the network has a different IP address.

10.2 > Technical Support and Hotline

North America:

Mail:

[email protected]

Tel: +1 888 940 7477

South America:

Mail:

[email protected]

Tel: +1 714 575 2973

Europe, Middle East, Africa:

Mail:

[email protected]

Tel: +33 1 30 20 30 40

Asia, Pacific:

Mail:

[email protected]

Tel: +91 1800 120 203 020

Web site

For the latest firmware, software, document releases, and news, please check our website :

www.biometric-terminals.com

To get your log in and password please contact your sales representative

Summary of Contents for VisionPass










































































Search results

Summary of Contents for VisionPass

Reviews:

Related manuals for VisionPass

Brands by name

Popular brands

Idemia VisionPass, Installation Manual

Search results

Summary of Contents for VisionPass

Reviews:

Related manuals for VisionPass

Brands by name

Popular brands