manualshive.com logo in svg

IDEC SE9Z-HC, Instruction Manual

Share
Download
IDEC SE9Z-HC Instruction Manual Download Page 16

15

Function Setting

<Inputting a password>

When the protective function is effective, “Lock” is shown on the lower section of the digital display. 

The functional settings of the 

SE4D

 series cannot be changed unless the password is input. Note that 

“

3-2-9 Protective Function

” is “locked” even when the protective function is ineffective.

Remarks

1) “

3-2-11 Setting Contents Monitoring Function

” is not “locked.”

2) Once the password is input, you do not need to input the password again till the power is 

turned OFF. (Except “

3-2-9 Protective Function

”) However, if the power is turned ON again 

without changing the protective function to ineffective, the password have to be input again 

since the protective function is still effective.

The procedure for inputting a password is as follows.

Input password

CH1

CH2

CH3

Complete inputting password

NG

NG

NG

Complete inputting password for 1 unit

Complete inputting password for 2 units

Summary of Contents for SE9Z-HC





































Reviews:

No comments

Brands by name

Popular brands

Load more brands