IDEAL Vogue System Gen 2 S15 Installation And Servicing Download Page 70

Page: 70 / 80

* All installations in England and Wales must be

to Local Authority Building Control (LABC) either directly or through a

Competent Persons Scheme. A Building Regulations Compliance

will then be issued to the customer.

www.centralheating.co.uk

This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating

compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.

GAS BOILER SYSTEM COMMISSIONING CHECKLIST

CONTROLS

Programmable room thermostat

Optimum start control

Combination Boiler

Fitted
Fitted
Fitted

Automatic bypass to system

Fitted

Boiler interlock

ALL SYSTEMS

Yes

CENTRAL HEATING MODE

mbar

Central heating return temperature

COMBINATION BOILERS ONLY

Yes
Yes

DOMESTIC HOT WATER MODE

mbar

Cold water inlet temperature

Yes

Temperature

CONDENSING BOILERS ONLY

Yes

ALL INSTALLATIONS

AND

² Ratio

AND

² Ratio

Yes
Yes
Yes
Yes

www.centralheating.co.uk

Summary of Contents for Vogue System Gen 2 S15

















































































Search results

Summary of Contents for Vogue System Gen 2 S15

Reviews:

Related manuals for Vogue System Gen 2 S15

Brands by name

Popular brands

IDEAL Vogue System Gen 2 S15, Installation And Servicing

Search results

Summary of Contents for Vogue System Gen 2 S15

Reviews:

Related manuals for Vogue System Gen 2 S15

Brands by name

Popular brands